CAT 627G manual Engine Stopping, Machine Operating Temperature Range, Machine Operation

Page 25

28

SEBU7858-03

Safety Section

 

Operation

 

Note: The shaded areas indicate the approximate location of areas with significant restricted visibility.

There is restricted visibility to the area directly be- hind the machine. Failure to make sure the area is clear could result in injury or death. Use a second person on the ground to make sure that the area is clear before you operate the machine in the RE- VERSE position. Refer to the Operation and Main- tenance Manual, “Operation Information” for more information.

i03565616

Operation

SMCS Code: 7000

Machine Operating Temperature Range

The standard machine configuration is intended for use within an ambient temperature range of −40 °C (−40 °F) to 50 °C (122 °F). Special configurations for different ambient temperatures may be available. Consult your Caterpillar dealer for additional information on special configurations of your machine.

Machine Operation

Only operate the machine while you are in a seat. The seat belt must be fastened while you operate the machine. Only operate the controls while the engine is running.

While you operate the machine slowly in an open area, check for proper operation of all controls and all protective devices.

Before you move the machine, you must make sure that no one will be endangered.

Do not allow riders on the machine unless the machine has the following equipment:

•additional seat

•additional seat belt

•Rollover Protective Structure (ROPS) Never use the work tool for a work platform.

Note any needed repairs during machine operation. Report any needed repairs.

Do not operate the machine on ground conditions that could result in the seat suspension travel stops being contacted and do not operate the machine at travel speeds that could result in the seat suspension travel stops being contacted. Operating this machine in very rough ground conditions or at travels speeds not suitable for the ground conditions may result

in excessive seat vertical travel with impact of the suspension against the travel stops, which may cause injury. In order to minimize impact loading on the operator, properly adjust the seat controls for the operator weight and height. Refer to Operation and Maintenance Manual, “Seat” for more information.

Carry attachments approximately 40 cm (15 inches) above ground level. Do not go close to the edge of a cliff, an excavation, or an overhang.

If the machine begins to sideslip downward on a grade, immediately remove the load and turn the machine downhill.

Avoid any conditions that can lead to tipping the machine. The machine can tip when you work on hills, on banks and on slopes. Also, the machine can tip when you cross ditches, ridges or other unexpected obstructions.

Avoid operating the machine across the slope. When possible, operate the machine up the slopes and down the slopes.

Maintain control of the machine. Do not overload the machine beyond the machine capacity.

Never straddle a wire cable. Never allow other personnel to straddle a wire cable.

Before you maneuver the machine, make sure that no personnel are between the machine and attachments.

Know the maximum dimensions of your machine.

Always keep the Rollover Protective Structure (ROPS) installed during machine operation.

i02624835

Engine Stopping

SMCS Code: 1000; 7000

Do not stop the engine immediately after the machine has been operated under load. This can cause overheating and accelerated wear of engine components.

Page 24 Page 26
Image 25
Page 24 Page 26
Contents DBD1-Up Machine DBZ1-Up Scraper Operation Maintenance ManualImportant Safety Information Smcs Code 7000 Safety MessagesSEBU7858-03 Safety Section Safety Messages G01954945 No Clearance Do Not OperateDo Not Weld On The ROPS/FOPS Structure Improper Connections For Jump Start Cables Seat BeltHigh Compressed Spring Engage The Apron Locking Pin Engine CoolantG01371640 Crushing Hazard Product Link 13 If EquippedAdditional Messages Air Conditioner Alternate ExitAuger Bearing Air TankData Privacy Hood BraceEngine Coolant General Hazard InformationSmcs Code Trapped Pressure Pressurized Air and WaterFluid Penetration Containing Fluid SpillageAsbestos Information Crushing Prevention and Cutting PreventionDispose of Waste Properly Oils Fire Prevention and Explosion Prevention Burn PreventionBatteries CoolantBattery and Battery Cables Lines, Tubes and Hoses WiringEther Fire Extinguisher LocationFire Extinguisher Electrical Storm Injury Prevention Tire InformationBefore Starting Engine Smcs Code 1000Before Operation Engine StartingVisibility Information Restricted Visibility Operation Machine Operating Temperature RangeEngine Stopping Machine OperationSlope Operation ParkingSound Information and Vibration Information Equipment Lowering with Engine StoppedSound Level Information Information Concerning Hand/Arm Vibration LevelWheel Scraper Work cycle Sources Guards Operator Protection Operator StationOther Guards If Equipped SEBU7858-03

627G specifications

The CAT 627G is a versatile and powerful motor grader designed for high-performance earthmoving and construction tasks. This machine combines advanced technology with robust engineering to provide operators with a reliable solution for grading, leveling, and shaping tasks in various terrains.

One of the standout features of the CAT 627G is its powerful C9.3 engine, which delivers high horsepower and torque, ensuring optimal performance even in the toughest conditions. This engine is coupled with a responsive transmission system, providing smooth operation and precise control over speed and power. The motor grader is designed for fuel efficiency, reducing operational costs while maximizing productivity.

The CAT 627G boasts a patented blade system that allows for exceptional cutting depth and precision. The blade can be easily adjusted for angle and height, enabling operators to adapt to different grading requirements quickly. With an impressive maximum blade lift height, this machine can handle large volumes of material effortlessly, making it ideal for applications such as road construction, site preparation, and ditching.

Another key characteristic of the CAT 627G is its operator-focused design. The cab is spacious and ergonomically designed, providing excellent visibility of the work area. The intuitive controls and advanced display systems allow for easy navigation of the machine’s functions, improving operator efficiency and reducing fatigue during long working hours. Additionally, the cab is equipped with climate control features, ensuring comfort regardless of external weather conditions.

The integration of advanced technologies sets the CAT 627G apart from other graders in its class. It comes with a comprehensive suite of grade control systems that enhance precision and accuracy in grading tasks. These systems can include GPS, laser guiding, and advanced feedback mechanisms, allowing operators to achieve optimal results with reduced manual effort.

Durability is a hallmark of the CAT 627G, with a robust frame and high-quality components designed to withstand rugged operating conditions. The maintenance-friendly design ensures that service and repairs can be performed quickly, minimizing downtime and keeping projects on schedule.

In summary, the CAT 627G is a powerful, efficient, and technologically advanced motor grader that meets the demands of modern construction and earthmoving projects. With its combination of a high-performance engine, innovative blade system, operator-centric design, and advanced technologies, it is a reliable choice for contractors seeking to enhance their operational efficiency and productivity.
Top Page Image Contents