Bush Hog 1035 manual Mounting Loader

Page 38

ASSEMBLY

ASSEMBLY

6.Remove linch pins and 1” hitch pins from loader upright.

7.Start tractor engine and release brakes. Retract bucket cylinders to allow parking stands to contact ground.

8.Extend lift cylinders 6” to 8” to rotate top of loader uprights forward out of the mount, allowing tractor to be pushed rearward. Retract bucket cylinders until lower loader upright pins clear mount pin saddles and front tires (See Figure Asm-L-0026).

9.Move tractor rearward approximately 6”, being certain not to stretch hydraulic hoses.

10.Stop tractor engine and set parking brake. Relax lift cylinders and bucket cylinders by moving each control lever in both directions. Disconnect hydraulic hoses from tractor.

11.Start tractor engine and release brakes. Slowly back tractor out of loader.

Mounting Loader

Mounting is basically reverse of dismounting.

1.Slowly drive tractor into loader approximately 6” from loader mounts. Shut off tractor engine and set parking brake.

2.Connect hydraulic hoses. Make sure couplers are clean before connecting together.

3.Start engine and release parking brake. Make sure lift cylinders are extended 6” to 8”. Stroke bucket cylinders to raise or lower upright pin to clear each front mount pin saddle by approximately 1” (See Figure Asm-L-0026).

4.Drive tractor forward until loader upright pins contact mount vertical stop surfaces just above the mount pin saddles (See Figure Asm-L-0026). Extend bucket cylinders to FULLY seat both loader upright pins into mount pin saddles and raise parking stands off ground. Retract lift cylinders, allowing tractor to move forward. Continue until loader uprights have fully seated into back of mount tube saddles by retracting lift cylinders to raise tractor front end (tires can be off ground).

5.Stop engine. Allow tractor front end to lower by relaxing ONLY lift cylinders with control lever.

6.Set parking braket. Insert two 1” hitch pins and linch pins.

7.Remove linch pins and clevis pins from parking stands, rotate stands into storage position and secure with clevis pins and linch pins (See Figure Asm-L-0024).

Note: If front wheel spacings were changed while loader was off tractor, tire clearances must be checked and possibly adjusted to ensure proper clearances.

1035 01/11

Assembly Section 3-6

© 2011 Alamo Group Inc.

Page 37 Page 39
Image 38
Page 37 Page 39
Contents 1035 Warranty Information To the Owner/Operator/DealerTable of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices1035 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 1035 01/11 Safety Section Safety SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 1035 01/11 Safety Section Parts Information Storage and Parking Safety Instructions and PracticesConcluding Safety Instructions and Practices Decal Location Instruct LogoModel ReflctrDecal Description Model NameD469 1035 01/11 Safety Section Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Assembly InstructionsProper Ballasting and Wheel Spacing Dismounting and Mounting Mid-Mount Loader Dismounting Loader Mounting Loader Attaching Pin on Bucket Page Operation Section Operation Standard Equipment and Specifications GPMOperator Requirements Operation Tractor Requirements Personal Protective Equipment PPETractor Ballast Rops and Seat BeltTractor Lighting and SMV Emblem Getting On and Off the Tractor Boarding the TractorDismounting the Tractor Starting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/Service Loader Pre-Operation Inspection/ServiceMount Assembly Bucket Inspection Loader Boom AssemblyHydraulic Line Inspection Do not Operate an Unsafe Tractor or Implement Do not Operate an Unsafe Tractor or Front END Loader Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation SL-33 Operation Operating the Loader Filling the BucketLifting the Load Carrying the Load Dumping the Bucket Lowering the BucketOperating with Float Control Loading from a BankOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Optional Attachment Shutting Down the Implement Loader StorageTransporting the Tractor and Implement Operation Operation Transporting on Public Roadways Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyProblem Possible Cause Remedy Page Maintenance Section Maintenance 1035 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Adjusting Bucket Level IndicatorCylinder Service Lift and Bucket Cylinder DisassemblyLift and Bucket Cylinder Reassembly StorageMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty Required of the Owner Required of the OperatorSOM-01/11 Printed U.S.A

1035 specifications

The Bush Hog 1035 is a versatile and robust rotary mower designed for agricultural and landscaping applications. Renowned for its durability and efficiency, this model is widely used by farmers and landowners who require a reliable tool for managing heavy brush, grass, and other vegetation.

One of the standout features of the Bush Hog 1035 is its heavy-duty construction. Built with a reinforced frame and high-quality materials, this mower can withstand rigorous use in various terrains. The 1035 boasts a mowing width of 35 inches, making it ideal for tackling medium to large areas while efficiently cutting through dense underbrush and grass.

Powering the Bush Hog 1035 is a reliable engine that provides ample horsepower to handle tough mowing conditions. Its efficient design allows for smooth operation and reduced fuel consumption, making it an economically sound choice for land management. The mower offers adjustable cutting heights, allowing users to select the appropriate length for different types of vegetation. This feature not only enhances cutting efficiency but also promotes healthier growth of the grass and plants left behind.

Another important aspect of the Bush Hog 1035 is the advanced cutting technology it utilizes. Equipped with high-quality, sharpened blades, the mower provides a clean and precise cut. The blades can be easily replaced or sharpened, ensuring consistent performance over time. Additionally, the mower's design minimizes clumping and promotes better debris dispersal, which is critical for maintaining an attractive landscape.

The Bush Hog 1035 is also designed for ease of use. Its intuitive controls and compact size make it maneuverable around obstacles, while the adjustable discharge chute directs grass clippings away from the cutting area, ensuring a tidy finish. The machine's low-profile design enhances stability on uneven ground, making it safer and easier to operate in challenging conditions.

Overall, the Bush Hog 1035 combines strength, efficiency, and user-friendly features, making it an excellent choice for anyone looking to manage their land effectively. Whether you are a professional landscaper or a homeowner with a large yard, the Bush Hog 1035 stands out as a reliable and effective tool for maintaining landscape health and appearance.
Top Page Image Contents