Bush Hog 1035 manual Storage, Lift and Bucket Cylinder Reassembly

Page 89
(SL-27)
(SL-26)

MAINTENANCE

Lift and Bucket Cylinder Reassembly

Note: Be careful not to damage seals and o-rings on edges or holes in cylinder tube. Inspect and remove burrs and sharp edges if necessary before reassembly.

1.Place rod seal (3) into groove inside cylinder head.

Note: Lips of seal (3) must be face inward and seal must be firmly seated in groove.

2.Install wiper seal (2) with lip of seal facing out and flush with top of cylinder head (5). Install wear ring (4) inside other end of head (5).

3.Place o-ring (7) with back-up washer (6) in groove on outside of head. Back-up washer must be on rod side.

4.Remove sharp edges on outer edge of the threaded end of shaft (1). Lubricate wiper seal (2) and rod seal

(3) in head and carefully slide head onto shaft.

5.Place o-ring (10), piston seal (11) and piston wear ring (8) in grooves on outside of piston (9). Note: For easier installation, place piston seal (11) in 120°F water to warm seal.

6.Slide piston (9) onto threaded end of shaft and install lock nut (12). Tighten lock nut to 100 lbs.

7.Lubricate piston wear ring (8) and piston seal (11) on piston, o-ring (7) and backup washer (6) on head and inside of cylinder tube (13), then carefully slide piston and head into cylinder tube (13).

8.Insert wire retaining ring (14) into slot in cylinder tube (13). Apply pressure to wire ring to thread it into groove while turning cylinder head.

Note: If cylinder has a countersunk hole, hook end of retaining wire into hole and turn cylinder head 1-1/2 turns to secure wire. End of hook may need to be ground to fit in countersunk hole.

Storage

Never crawl under or allow children to play around or on a loader that is disconnected from the tractor. The loader could fall crushing a person resulting in serious injury or death. (SL-13)

Do not remove the attachment from the loader when the loader is disconnected from the tractor. The attachment stabilizes the loader. If the attachment is removed, the loader will fall and could result in serious injury.

Only disconnect and store the loader on firm flat ground. Make sure the loader stands are properly installed and rest on firm ground or support blocks. If the stands sink or fail, the loader could fall causing serious injury.

NOTE: When loader hydraulics are disconnected from tractor, the tractor hydraulic circuit must be completed. Failure to do so will result in tractor hydraulic pump damage.

1035 01/11

Maintenance Section 5-7

© 2011 Alamo Group Inc.

MAINTENANCE

Page 88 Page 90
Image 89
Page 88 Page 90
Contents 1035 To the Owner/Operator/Dealer Warranty InformationTable of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety1035 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 1035 01/11 Safety Section Safety SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 1035 01/11 Safety Section Parts Information Storage and Parking Safety Instructions and PracticesConcluding Safety Instructions and Practices Decal Location Model LogoInstruct ReflctrModel Name Decal DescriptionD469 1035 01/11 Safety Section Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions AssemblyProper Ballasting and Wheel Spacing Dismounting and Mounting Mid-Mount Loader Dismounting Loader Mounting Loader Attaching Pin on Bucket Page Operation Section Operation GPM Standard Equipment and SpecificationsOperator Requirements Operation Personal Protective Equipment PPE Tractor RequirementsTractor Ballast Rops and Seat BeltTractor Lighting and SMV Emblem Boarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Pre-Operation Inspection and Service Loader Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceMount Assembly Bucket Inspection Loader Boom AssemblyHydraulic Line Inspection Do not Operate an Unsafe Tractor or Implement Do not Operate an Unsafe Tractor or Front END Loader Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation SL-33 Operation Filling the Bucket Operating the LoaderLifting the Load Carrying the Load Lowering the Bucket Dumping the BucketLoading from a Bank Operating with Float ControlOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Optional Attachment Shutting Down the Implement Loader StorageTransporting the Tractor and Implement Operation Operation Transporting on Public Roadways Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideProblem Possible Cause Remedy Page Maintenance Section Maintenance 1035 01/11 Maintenance Section Lubrication Schedule Adjusting Bucket Level Indicator Daily MaintenanceLift and Bucket Cylinder Disassembly Cylinder ServiceStorage Lift and Bucket Cylinder ReassemblyMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty Required of the Operator Required of the OwnerSOM-01/11 Printed U.S.A

1035 specifications

The Bush Hog 1035 is a versatile and robust rotary mower designed for agricultural and landscaping applications. Renowned for its durability and efficiency, this model is widely used by farmers and landowners who require a reliable tool for managing heavy brush, grass, and other vegetation.

One of the standout features of the Bush Hog 1035 is its heavy-duty construction. Built with a reinforced frame and high-quality materials, this mower can withstand rigorous use in various terrains. The 1035 boasts a mowing width of 35 inches, making it ideal for tackling medium to large areas while efficiently cutting through dense underbrush and grass.

Powering the Bush Hog 1035 is a reliable engine that provides ample horsepower to handle tough mowing conditions. Its efficient design allows for smooth operation and reduced fuel consumption, making it an economically sound choice for land management. The mower offers adjustable cutting heights, allowing users to select the appropriate length for different types of vegetation. This feature not only enhances cutting efficiency but also promotes healthier growth of the grass and plants left behind.

Another important aspect of the Bush Hog 1035 is the advanced cutting technology it utilizes. Equipped with high-quality, sharpened blades, the mower provides a clean and precise cut. The blades can be easily replaced or sharpened, ensuring consistent performance over time. Additionally, the mower's design minimizes clumping and promotes better debris dispersal, which is critical for maintaining an attractive landscape.

The Bush Hog 1035 is also designed for ease of use. Its intuitive controls and compact size make it maneuverable around obstacles, while the adjustable discharge chute directs grass clippings away from the cutting area, ensuring a tidy finish. The machine's low-profile design enhances stability on uneven ground, making it safer and easier to operate in challenging conditions.

Overall, the Bush Hog 1035 combines strength, efficiency, and user-friendly features, making it an excellent choice for anyone looking to manage their land effectively. Whether you are a professional landscaper or a homeowner with a large yard, the Bush Hog 1035 stands out as a reliable and effective tool for maintaining landscape health and appearance.
Top Page Image Contents