Krell Industries EVOLUTION TWO MONAURAL PREAMPLIFIER manual Display

Page 40

(SECTION SEVEN: Customizing the Evolution Two continued)

CLONE BEGIN

Sends the message that a clone is about to begin, from the clone transmitter to the clone receiver(s).

CLONE TRANSMIT

Once the clone begin message is sent, the clone transmitter display reads: CLONE TRANSMIT, indicating that the preamplifier is ready to transmit the clone data.

CLONE RECEIVE

Once the clone begin message is sent, the clone receiver(s) display reads: CLONE RECEIVE, indicating that the preamplifier(s) is(are) ready to receive the clone data.

Note

In order to set a clone receiver to ignore the clone, use the level control knob on the clone

receiver front panel to scroll to CLONE IGNORE.

Display

17 Menu Button or Key Enter or exit the menu.

16 Volume Knob or Level Keys

Navigate the menu hierarchy, review functions and configu- ration options.

18 Enter Button or Key Select a configuration option or confirm a selection.

BACK

Scroll up the menu hierarchy, or exit a menu option without confirming it.

This function enables you to turn on the front panel display (15) all the time, or turn it off after a time out. The options are: ON, TIMED.

Enter the menu, then:

1.Use the level control knob on the preamplifier chassis front panel or the up and down keys on the remote control (16) to select: DISPLAY.

2.Press the enter button on the preamplifier chassis front panel or the enter key (18) on the remote control. The front panel display (15) reads: MODE.

3.Press the enter button or key (18) again. The front panel display shows the default mode: ON.

4.Use the level control knob or the up and down keys to select the desired option: ON or TIMED.

5.Press the enter button or key to confirm the selection. The front panel display reads: MODE.

6.Use the level control knob or the up and down keys to select: BRIGHTNESS.

7.Press the enter button or key. The front panel display shows the default mode:

HIGH.

8.Use the level control knob or the up and down keys to select the desired

brightness: OFF, LOW (25%), MED (50%), or HIGH (100%).

9.Press the enter button or key to confirm the selection. The front panel display

reads: BRIGHTNESS.

36

Image 40

Contents Evolution Page Contents List of Illustrations Letter from Dan D’Agostino Letter from Dan D’Agostino About Krell Krell LegacyVoltage Signal Transmission Traditional Audio System How Cast and Krell Current Mode InteractRevolutionary Krell Cast Technology Cast BasicsEvolution Cast Cast Cable ConstructionBest Musical Performance Ensuring Maximum Performance Zero Feedback Balanced Current Mode DesignCore Technologies Fully Balanced Discrete Volume Control Separate Power SupplyAdvanced Microprocessor Control Custom Software Definition of Terms ConfigurationsInputs and Outputs Krell Current Mode PreamplifierOperation TechnologyUnpacking and Placement Opening the Evolution Two Shipping CartonLeft/Right Channel Orientation To Remove the Preamplifier Channel from the Shipping CartonAC Power Guidelines PlacementRepeat Steps 1-5 for the remaining preamplifier channels Connecting the Evolution Two to Your System Quick StartOperating the Evolution Two Linked Mode Anatomy of an Evolution Two 11 12 13Evolution Two Remote Control Power Front Panel DescriptionChassis Remote Functions on the Front PanelPreamplifier Functions DisplayLevel Control Navigate/CustomizeMenu Button or Key Enter Button or KeyRemote Control Description Battery Installation and RemovalCompact Disc Functions Amplifier FunctionsIEC Power Cord Receptacle Back Panel Description InputsOutputs 35, 36 Main Bus OutputsRemote Connections on the Back Panel 37, 38 Record Bus Outputs42 RC-5 43 RS-232Phono Stage Connector Link ControlConnecting the Evolution Two to Your System XLR Pin ConfigurationInput and Output Connections Connection StepsNever connect two power supplies together Connections Using can Link To Connect Multiple Evolution Two Preamplifiers via can LinkOn/Off and Stand-by Operation Linked Mode Evolution Two OperationPlay and Record To Turn Off Your SystemOperation Using can Link Customizing the Evolution Two Navigation Conventions Menu Functions AC Mains Backlight Enter the menu, thenChannel Assign BalanceUse to make a left channel respond as a right channel Clone Use to make a right channel respond as a left channelDisplay Front panel display is always on InfoFront panel display times out after 5 seconds Input Name Input Level TrimTo select input names for other inputs, repeat Steps 3 Input Phase Phase of the selected input is unaffectedPhase of the selected input is inverted 180 degrees Input TriggerEvolution Two responds to 12 V input trigger commands IR Out ControlLink Control can Link Output Trigger MuteOutput of the Evolution Two is completely silenced RC-5 Control Recall Recalls the factory settingsRS-232 Control Save Software CloneBegins the software clone process Tape InputInitiates the software clone Theater Mode Volume Display +12 dB. The options are Enter the menu, thenQuestions and Answers Troubleshooting System Noise Appendix can Link and Multiple Evolution Two Preamplifiers Connection of multiple preamplifier channelsAppendix can Link and Multiple Evolution Two Preamplifiers Warranty Warranty Return Authorization Procedure To contact the Krell Service DepartmentService@krellonline.com AM to 500 PM ESTSpecifications Control outputs