Black & Decker GH610 Maintenance, Troubleshooting Tool Runs Slowly, Replacing the Spool

Page 10

• Wind the cutting line onto the spool in

 

 

 

 

 

 

 

 

the direction of the arrow on the spool.

16

 

 

 

 

 

 

Make sure to wind the line on neatlyand

 

 

 

 

in layers.Do not crisscross(figure 16).

 

 

 

 

• When the wound cutting line reaches

 

 

 

 

the recesses (x), cut the line. (figure 15).

 

 

 

 

• Fit the spool onto the tool as described

 

 

 

 

in “REPLACING THE SPOOL”.

 

 

 

 

 

 

 

 

CAUTION: Before you begin

 

 

 

 

 

 

 

 

trimming, only use the appropriate type of

 

 

 

 

cutting line.

 

 

 

 

MAINTENANCE

WARNING: To avoid serious injury, switch off and unplug the tool before performing any maintenance.

1. Keep the air intake slots clean to avoid overheating.

2. Your trimmer line can dry out over time. To keep your line in top condition, store spare pre-wound spools or bulk line in a plastic, sealable bag with a tablespoon of water.

3. Plastic parts may be cleaned by using a mild soap and a damp rag.

4. The line cutter on the edge of the guard can dull over time. It is recommended you periodically touch-up the sharpness of the blade with a file.

IMPORTANT:To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

TROUBLESHOOTING TOOL RUNS SLOWLY

• Check that the spool housing can rotate freely. Carefully clean it if necessary.

• Check that the cutting line does not protrude more than approximately 5-3/8 inches (136mm) from the spool. If it does, cut it off so that it just reaches the line trimming blade.

AUTOMATIC LINE FEED DOES NOT WORK

• Keep the tabs depressed and remove the spool from the spool housing in the trimmer head.

• Pull the cutting line until it protrudes approximately 5-3/8 inches (136mm) from the spool. If insufficient cutting line is left on the spool, install a new spool of cutting line.

• Ensure that the line is not crisscrossed on the spool as detailed in figure 16. If it is, unwind the cutting line, then wind it back on the spool neatly so that the lines do not cross.

• Align the tabs on the spool cap with the cut outs in the housing.

• Push the spool cap onto the housing until it snaps securely into place.

• If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade. If the automatic line feed still does not work or the spool is jammed, try the following suggestions:

• Carefully clean the spool and housing.

• Remove the spool and check if the lever in the spool housing can move freely.

• Remove the spool and unwind the cutting line, then wind it on neatly again. Replace the spool into the housing.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Trimmer / Edger Table of Contents InstructionsMaintain Appliances with Care Follow instructions Safety Warnings Instructions Polarized Plugs Safety Warnings Instructions Extension CordsComponents Assembly & Adjustment Assembly Tools Required not SuppliedHeight Adjustment Attaching the Auxiliary HandleOperating Instructions Switching on and OFFConvert to Edging Mode Attaching Extension CordReplacement Accessories Replacing the Spool Figures 11,12,13Spool ReplacingRewinding Spool from Bulk Line Troubleshooting Tool Runs Slowly MaintenanceReplacing the Spool See ʻTools-Electricʼ Service Information Full TWO-YEAR Home USE WarrantyFor Service & Sales Black & Decker U.S. IncTAILLE-BORDURE / COUPE- BORDUREMODED’EMPLOI Avertissements DE Sécuritéet Directives Depremièreimportance Page Avertissements DE Sécurité ET Directives Fiches Polarisées Conserver CES MesuresComposants TensionFixation DE LA Poignee Assemblage ET RéglagePose DU PARE-MAIN AuxiliaireReglage DE LA Hauteur Fixation DE LA RallongeMise EN Marche ET Arret Convertir AU Mode COUPE-BORDUREFIL Tranchant / Avance DU FIL Composer le 1-800-544-6986 ou consulter Accessoires DE RechangeRemplacer LA Bobine Section « Remplacer LA Bobine »LʼOUTIL Fonctionne Lentement Remplacement Gratuit DES Etiquettes Outils électriquesPodadora / Bordeadora Manual DE Instrucciones Utilice LA Vestimenta Adecuada no utilice ropa holgada Importantes Sobre SeguridadSiempre Utilice Protección Para LOS Ojos utilice LA Cuerda Giratoria Realiza UNA Función DE CorteNo sumerja la herramienta en agua ni la salpique con una Seguridad Cables Prolongadores Instrucciones Y Advertencias DESeguridad Enchufes Polarizados Mango auxiliar ComponentesInterruptor Guía de borde Protector CarreteQUE no Están Provistas Ensamblaje Y AjusteHerramientas QUE SE Requieren Para EL Ensamblaje Colocacion DEL Mango AuxiliarAjuste DE Altura Instrucciones DE OperaciónColocacion DEL Cable Prolongador En la figura Encendido Y ApagadoConversión AL Modo DE Bordeado Cuerda DE CORTE/ALIMENTACIÓNDE LA CuerdaAccesorios DE Repuesto Reemplazo DE CarretesUtilice Solo CUERDADEDIAMETROREDONDADE1,7MM MantenimientoRebobinado DEL Carrete CON Cuerda a Granel Reemplazo DEL CarreteDeteccion DE Problemas LA Herramienta Funciona Lentamente LA Alimentacion Automatica DE LA Cuerda no FuncionaGarantia Completa DE DOS Anos Para USO EN EL Hogar Name · Nombre Años DE Garantia Esta Garantia no Aplica CuandoSolamente Para Propositos DE Mexico

GH610 specifications

The Black & Decker GH610 String Trimmer is a versatile and powerful garden tool designed to tackle a variety of trimming and edging tasks in residential gardens. With its lightweight design and user-friendly features, it is an excellent choice for homeowners looking to maintain their lawns efficiently.

One of the standout features of the GH610 is its 6.5 amp motor, which provides ample power for cutting through even the toughest grass and weeds. This robust motor allows the trimmer to deliver a cutting swath of 14 inches, making it ideal for larger areas without the need for extensive trimming time. The additional power ensures that users can quickly finish their trimming tasks, leaving more time for enjoyment in the garden.

Equipped with a dual-line feed, the GH610 allows for continuous use without interruptions. The trimmer automatically feeds the line as needed, ensuring a consistent cutting experience. The 0.065-inch line diameter is capable of handling heavy growth, making it effective for both basic lawn care and more demanding landscaping tasks.

The GH610's ergonomic design significantly enhances user comfort. The adjustable handle allows users to customize the grip to their needs, reducing fatigue during extended use. Additionally, it features an automatic height adjustment system, ensuring optimal positioning for users of different heights. This consideration for user ergonomics makes the GH610 a favorite among homeowners who require a tool that balances power with comfort.

Another noteworthy characteristic of the Black & Decker GH610 is its easy storage capability. The trimmer features a collapsible design that allows for efficient storage in small spaces. Whether placed in a garage or a shed, the compact design is particularly beneficial for those with limited storage options.

Furthermore, the GH610 incorporates cutting-edge technologies to enhance its operation. The built-in cord retention system prevents accidental disconnections during use, allowing for uninterrupted trimming tasks. This thoughtful design feature ensures that users can focus on their work without the hassle of re-plugging the trimmer.

In conclusion, the Black & Decker GH610 String Trimmer combines power, user comfort, and innovative features to create an ideal tool for lawn maintenance. With its impressive motor, adjustable handle, and automatic line feed, this trimmer stands out as a reliable choice for tackling a variety of gardening tasks efficiently.
Top Page Image Contents