Billy Goat FM3301EB owner manual Belt Replacement, Blade Drive Belt

Page 14

FM Owner’s Manual

BELT REPLACEMENT

When replacing one belt the other should be inspected for wear and replaced if worn. It is good practice to change both belts when either is worn beyond use. Use only original equipment belts for replacement. Billy Goat uses only premium quality, Kevlar corded and coated belts in your unit. Substitute belts do not meet the design and performance requirements for your unit, and will greatly reduce machine performance and belt life.

Blade Drive Belt

Tools required: ratchet, 3/4 inch socket, 10” extension bar for socket, two ½” wrenches and adequate support for machine.

1. Disconnect spark plug wire.

2. Remove the deck belt cover.

3.Support front of unit to allow access to underside of the machine near the engine. Note: Unit is heavy. Be sure support is adequate to prevent personal injury.

4.Observe the orientation of the belt fingers (Item 90) under the engine.

5.Remove the 4 engine mount bolts (Item 48) being careful not to let engine slide out of place.

6.Remove the left and right belt fingers (These fingers are interchangeable).

7.Observe the orientation of the belt finger (Item 91) on idler (Item 50).

8.Loosen but do not remove idler/belt finger retaining nut (Item 144).

9.Observe belt routing and remove the belt from front spindle pulley (Item 46).

10.Remove the belt from the idler pulley and from the engine pulley.

11.Install new belt on engine pulley, idler and front spindle pulley following the original belt routing.

12.Position the idler belt finger centered on idler bracket and tighten the retaining nut (Item 144).

13.Reinstall the left and right belt guide fingers under the engine base using all fasteners in the exact order they were removed.

NOTE: Before installing the fasteners inspect them for wear and replace as necessary.

14.Torque the four engine bolts to 40 ft-lbs.

Note: With clutch levers engaged, be sure belt guides do not touch belts after installation, there should be 1/8” clearance between the belt and the guides.

15.Observe the idler pulley when the blade drive lever is lowered and released (see figure 17-7).

NOTE: Idler should tighten the belt when blade drive lever is pressed and the belt should be slack when the lever is released. With the lever depressed, the edge of the belt guide should not rub on the belt.

16.Replace the cover

17.Reconnect spark plug wire.

18.Start engine and check for proper operation of blade drive system.

Spindle Drive Belt

Tools required: 3/8 inch socket, 1/2 inch socket.

1. Disconnect spark plug wire.

2. Follow steps to remove the Blade Drive Belt (on the spindle pulley side only) from the previous section.

3. Loosen the two idler plate nuts (Item 143).

4. Slide the belt idler to release the belt tension.

5. Observe the belt routing, then remove the old belt and install the new belt using the original routing.

6. Tension the belt using a long screwdriver or other pry bar to push the idler pulley against the belt.

Note: Take care not to damage the idler pulley.

7.Tighten the two idler plate nuts just enough to avoid slippage while checking the belt tension.

8. Check belt deflection. Finger pressure should give 0.5” to 0.75” (see figure 17-8).

9. Increase/decrease belt tension for proper deflection.

10. Finish tightening the two idler plate nuts.

11. Follow steps to reinstall Blade Drive Belt from the previous section.

12. Replace cover.

13. Reconnect spark plug wire.

Part No 520187

14

Fig. 17-6

Fig. 17-7

Fig. 17-8

Form No F010408A

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Billy Goat Finish Mower Contents About this ManualSpecifications Serial Plate DataGeneral Safety Instructions and Symbols Form No F010408A Intended USE SoundVibration Data Throttle Controls and Labels Instruction LabelsEngine Labels Packing Checklist PUT OIL in Engine Before StartingAssembly Storage OperationHandling & Transporting Cutting Height Adjustment Cutting OperationHillside Mowing Blade ClutchPropulsion Maintenance Periodic MaintenanceBelt Replacement Blade Drive BeltBelt Replacement Cable AdjustmentsBrake Puck Replacement Starter Switch WiringTroubleshooting Warranty Claim ProcedureParts Drawing FM Parts List QTYBattery is included 104 140 151 147 143 183 190 123 Label HOT Engine Belt Layout Description QTYTo Trans Description Mulching KIT P/N AccessoriesGrass Catcher KIT P/N Transaxle Guard KIT P/NMaintenance Record Form No F010408A

FM3301EB specifications

The Billy Goat FM3301EB is a powerful and versatile forced air fan designed to optimize the efficiency of various outdoor tasks. Engineered with the needs of both professionals and DIY enthusiasts in mind, this model offers a range of features that make it a standout choice in the market.

One of the key characteristics of the FM3301EB is its robust 228cc commercial grade engine, which provides substantial airflow and excellent performance. The engine is designed to deliver high airflow rates, enabling efficient operation for a variety of applications such as landscape maintenance, construction, and even debris cleanup. The powerful engine allows the fan to project air at impressive distances, making it effective for larger areas that need to be dried or cleared.

The FM3301EB boasts an ergonomically designed housing, which not only contributes to its durability but also aids in easy handling and transport. Weighing in at just around 70 pounds, it is relatively lightweight for its class, which means users can quickly move the fan to various job sites. Additionally, the rugged design ensures it can withstand the rigors of industrial use without compromising performance.

Another standout feature of the Billy Goat FM3301EB is its innovative impeller design, which enhances airflow efficiency. The fan features a specifically designed blade system that maximizes air movement while minimizing noise levels. This makes it an ideal choice for environments where noise reduction is crucial, such as residential areas or quiet job sites.

The FM3301EB also includes a variety of operational options, including adjustable airflow directions. This adaptability allows users to direct airflow exactly where it is needed, whether for drying surfaces or clearing debris. The easy-to-use controls make adjustment quick and intuitive, ensuring minimal downtime during demanding tasks.

In summary, the Billy Goat FM3301EB stands out for its powerful engine, durable construction, innovative impeller design, and user-friendly features. It's a reliable tool that offers efficiency and versatility, making it a valuable addition to the arsenal of anyone in landscaping, construction, or maintenance. Whether you are looking to enhance productivity or simply need a reliable airflow solution, the FM3301EB is crafted to deliver exceptional performance in a variety of settings.
Top Page Image Contents