Billy Goat CR550HCV specifications General Engine Specifications, Troubleshooting, Unit Storage

20TROUBLESHOOTING

Problem

Before Requesting Service Review These Suggestions

Possible Cause Solution

Engine stalls or labors when raking.	Blades set too deep into ground	Raise blades so that they just touch the ground on a
		level surface.
Abnormal vibration.	Damaged or missing blades. Loose handle bolts.	Stop work immediately. Replace any damaged or
	Loose engine bolts	missing blades. Tighten all loose bolts and nuts.
Engine will not start.	Stop switch off (Honda only). Throttle in off position.	Check stop switches, throttle, choke position and
	Engine not in full choke position. Out of gasoline. Bad	gasoline. Connect spark plug wire. Clean or replace
	or old gasoline. Spark Plug wire disconnected. Dirty air	air cleaner. Contact a qualified service person.
	cleaner. Engine oil level too low (Honda only).
Engine is locked, will not	Debris locked against reel, or drive pulleys. Engine	Pull spark plug wire and remove debris. Contact an
pull over.	problem.	engine servicing dealer for engine problems.

ENGINE

GENERAL ENGINE SPECIFICATIONS

ENGINE	HORSEPOWER	MODEL NO.	GOVERNED RPM
HONDA	5.0	GC160AQHA	3600

When servicing engine refer to specific manufacturers engine owner's manual. All engine warranty is covered by the specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing engine dealer. When contacting a dealer for service it is a good idea to have your engine model number available for reference(See table page above). If you can not locate a servicing dealer in your area you can contact the manufacturers national service organization.

To reach:

American Honda: 800-426-7701

22.1Engine Service and Warranty

Contact your nearest engine manufacturer's authorized servicing dealer. (See page 7)

21	Serial Plate	Record your machine model, serial number and
		date-of-purchase and where purchased

	1803 S. Jefferson
	Lee's Summit,
	MO 64062 / USA
	Tel (816) 524-9666
R	Fax (816) 524-6983

ModelSerial No.

99 dB
	Unit(Weight)			Engine Power
		lbs.	kg		kW	rpm
						min-1

Purchase Purchased

Datefrom

UNIT STORAGE

Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.

If engine is to be unused for 30 days or more, prepare as follows:

Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Be sure engine is cool. Do not smoke. Run engine until fuel tank is empty and engine runs out of gasoline.

NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 min. after adding stabilizer to allow it to reach the carburetor.

22WARRANTY PROCEDURE

Should a Billy Goat Machine fail due to a defect in material and/or workmanship, the owner should make a warranty claim as follows:

-The Machine must be taken to the dealer from whom it was purchased or to an authorized Servicing Billy Goat Dealer.

-The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt. -The Warranty Claim will be completed by the authorized Billy Goat Dealer and submitted to their respective Billy Goat Distributor for their territory. Attention: Service Manager. Any parts replaced under warranty must be tagged and retained for 90 days.

-The distributor service manager will sign off on the claim and submit it to Billy Goat for consideration.

-The Technical Service Department at Billy Goat will study the claim and may request parts to be returned for examination. Billy Goat will notify their conclusions to the distributor service manager from whom the claim was received.

-The decision by the Quality / Service department at Billy Goat to approve or reject a Warranty claim is final and binding.

Note: To process a Warranty Claim, it is necessary to quote the Model & Serial Number which are printed on the Billy Goat Serial Plate (See owner’s manual).

	BILLY GOAT INDUSTRIES INC.
	1803 S.W. JEFFERSON / LEE'S SUMMIT, MO 64082-2312 / USA
R	PHONE: 816-524-9666 FAX: 816-524-6983	www.billygoat.com

Part No. 350245 Page 12 of 12 Form No. F021604A