Bad Boy Mowers PUP Series, 48031001 Cam Assembly Adjustment, Mount Tube Stiffener Installation

Page 7

2-4 Cam Assembly Adjustment

Figure 7.

The cam assembly P#(A0422), which controls the blower belt tension, comes from the factory pre-adjusted. If the belt is too tight or becomes too loose, remove the hair pin clip P#(K0099) from the belt tension rod P#(K0326) and pull the “L” end of the rod out of its hole in the cam assembly. The tension rod may then be screwed out to tighten the belt or screwed in to loosen the belt. Replace the “L” end into the top hole in the cam and replace the hair pin clip. Adjust the cam stop bolt P#(K1159) to allow the cam to rotate slightly over center when the blower is disengaged (Figure 6).

Figure 6.

Cam Assy.

Lower Mount Tube

Bad Boy Receiver Hitch

Fasten Here w/

(1)5/8” x 3” Clevis Pin

(1)Hair Pin Clip

 

 

2-6 Mount Tube Stiffener Installation

 

 

Place the lower mount tube stiffener P#(B0247) between

 

 

the lower mount tube (previously installed) and the

 

 

mower’s rear frame positioning the bend flaps

 

 

downwards (Figure 8). Fasten to the mower’s rear frame

 

 

by using (2) ½”-13 x 1” HHCS P#(K1231), (2) fender

 

 

washers P#(K0041) and (2) ½”-13 flange nuts

Cam Stop

 

P#(K1246). Fasten to the lower mount tube by using (1)

Tension Rod

3/8”-16 U-bolt P#(K1432) and (2) 3/8”-16 flange nuts

Bolt

 

P#(K1215). Tighten all nuts and bolts.

 

 

2-5 Lower Frame Installation

Figure 8.

Fasten w/

(1) 3/8” U-Bolt

(2) 3/8” Flange Nuts

NOTE: Before continuing installation, you must install the Bad Boy Pup Series bolt-on hitch P#(093-1112-00) for the rear of the mower. Adding this hitch is required for mounting the collection system. Contact Bad Boy to purchase at (870) 698-0090.

Slide the short leg of the lower mount tube P#(B0246) into the Bad Boy bolt-on hitch previously installed. Align the hole in the mount tube to the bolt-on hitch and fasten by using (1) 5/8” x 3” clevis pin P#(K0172) and (1) 5/32” x 2-5/8” hair pin clip P#(K0088) (Figure 7).

Lower Mount TubeLower Mount Tube Stiffener

Fasten w/ (2) ½” x1” HHCS

(2)Fender Washers

(2)½” Flange Nuts

7

Image 7
Contents $4.00 REV OPERATOR’S ManualPTO Grass Collection System Table of ContentsSafety Alert Symbol Safety Signs SafetyWhat is WARRANTED? Peco Limited Warranty for NEW ProductsPreparation Of Mower Section Introduction and DescriptionIntroduction DescriptionPTO Assembly Installation Belt Installation Mount Tube Stiffener Installation Cam Assembly AdjustmentLower Frame Installation Carriage Bolt Exploded Parts View Parts View Assembly Installation Upper Frame Assembly InstallationBoot To Mower Deck Installation Top Assembly To Upper FrameImpeller Blade Removal/Replacement Blower Cone InstallationLower Hose To Boot Installation Lengths Of Hose AdjustmentUpper Hose Installation Lower Hose To Blower Cone InstallationInstallation/Removal Collection Bags Section Operating Instructions Section MaintenanceParts And Service Information Section Parts and ServiceLubrication Safety Decals Bad Boy Page Contact Bad Boy Today

PUP Series, 48031001 specifications

Bad Boy Mowers has long been synonymous with quality and power in the lawn care industry, and their PUP Series, specifically the model 48031001, is a testament to that legacy. Designed with both home users and commercial landscapers in mind, this mower brings an impressive blend of features, technologies, and user-friendly characteristics that set it apart from the competition.

At the heart of the PUP Series 48031001 is its robust engine. The mower is equipped with a powerful, reliable engine that provides sufficient torque and speed to tackle even the densest grass. This high-performance engine is teamed with a heavy-duty cutting deck, which ensures a clean and precise cut every time. The cutting deck features a unique design that enhances airflow, resulting in better grass discharge and a superior cut quality.

User comfort is a significant priority in the design of the PUP Series. The mower comes with an ergonomic seat and control setup, allowing operators to easily manage their mowing tasks without unnecessary strain. The easy-to-use control panel places all essential functions within easy reach, promoting a seamless mowing experience.

Durability is a hallmark of the Bad Boy Mowers brand, and the PUP Series 48031001 is no exception. The mower is built with a solid steel frame and high-quality components, ensuring it can withstand the rigors of regular use. Its rugged construction means that it’s not just built to last; it's built to perform, season after season.

Another key feature of the PUP Series is its enhanced maneuverability. With a compact design and a tight turning radius, this mower allows for easy navigation in tight spots around flower beds or trees, making it an excellent choice for residential properties with unique landscaping.

Moreover, the mower is designed with maintenance ease in mind. Accessible parts and a user-friendly design allow owners to perform regular maintenance tasks with minimal hassle, which is critical for keeping the mower in peak operating condition over time.

Safety features in the PUP Series 48031001 include an operator presence system that automatically shuts off the engine when the operator leaves the seat, preventing accidents and ensuring peace of mind during operation.

In conclusion, the Bad Boy Mowers PUP Series 48031001 combines power, comfort, and durability with thoughtful safety and maintenance features, making it an outstanding choice for anyone seeking a reliable and efficient mowing solution. Whether for residential or commercial use, it promises to make mowing an effortless and enjoyable task.