Troubleshooting the Rider

TROUBLESHOOTING

While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies.

If you prefer, all of these procedures can be performed by your local authorized dealer.

WARNING

To avoid serious injury, perform maintenance on the rider or mower only when the engine is stopped, the ground speed levers are set to START/PARK, and the parking brake lever is set to

ENGAGE.

Always remove the ignition key, disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance, to prevent accidental starting of the engine.

PROBLEM	CAUSE		REMEDY

Engine will	Ignition switch not turned fully to START position.		Turn ignition switch fully to START position.
not turnover.
	Ground speed levers not set to START/PARK.		Set to START/PARK.

	Mower blade switch in ON position.		Place in OFF position.

	Parking brake lever in DISENGAGE position.		Set to ENGAGE position.

	Battery terminals require cleaning.		Clean the battery termi als

	Battery discharged or dead.		Recharge r replace.

	Wiring loose or broken; connector separated.		Visually check w ring & replace broken or frayed
			wires. T gh en l se connections.

	Safety interlock switch faulty.		Repla	e. Con act your local authorized dealer.

	Solenoid or starter motor faulty.		Repla	e. Contact your local authorized dealer.

Engine will	Engine is cold; choke not in CLOSED position.		Move choke to CLOSED position.
turnover but
	Engine is warm; choke not in OPEN p sition.		Move choke to OPEN position.
will not start.
	Engine flooded.		Set choke to OPEN position when cranking engine.


	Out of fuel.		Allow engine to cool, then refill the fuel tank.

	Fuel is old or stale, or water in fuel.		Drain fuel & replace with fresh fuel. Contact your
			local authorized dealer.

	Spark plug(s) faulty, foul or incorr ctly gapped.		Clean and gap or replace.

	Safety interlock switch faulty.		Replace. Contact your local authorized dealer.

Engine starts	Air filter plugged		Service pre-cleaner and/or replace air filter
hard or runs			element.
poorly.
	Choke not set to CLOSED position when		Set choke to CLOSED when cranking. Set choke
		Reproduction
	cranking the engine, OR choke not set to OPEN		to OPEN when engine is running. A warm engine
	after engine starts.		may not require choking.

	Spark plug faulty, fouled, or incorrectly gapped.		Clean and gap or replace.

Engine	Low oil level.		Check/add oil as required.
knocks.
	Using wrong grade oil.		See "Change Engine Oil" in the Maintenance
			Section.

Excessive oil	Engine running too hot.		Clean engine cooling fins, blower screen and air
consumption.			cleaner.

	Using wrong weight oil.		See "Change Engine Oil" in the Maintenance
			Section.

	Too much oil in crankcase.		Drain excess oil.

Engine	Dirty air filter or pre-cleaner, or both.		Service or replace as required. See Maintenance
exhaust is			Section.
black.
	Choke set to CLOSED when engine is running.		Set choke to OPEN as soon as engine starts.

ZT2142, CZT2142, ZT18533 specifications

The Axion ZT18533, ZT2142, and CZT2142 are prime examples of advanced agricultural technology, designed to enhance operational efficiency and productivity on the farm. These versatile machines represent a significant leap in the integration of power and precision farming practices.

The Axion ZT18533 is equipped with a robust engine, providing exceptional horsepower and torque for demanding farm tasks. This model boasts a high-performance transmission system that ensures seamless power delivery, allowing operators to tackle varied terrain effortlessly. Key features include advanced GPS steering technology, which enhances navigation accuracy, while the intuitive control interface ensures ease of use for operators of all experience levels.

Similarly, the ZT2142 model shines with its innovative engine design, featuring stringent emission controls to comply with modern environmental standards. This model places a strong emphasis on fuel efficiency, offering innovative technologies such as common rail fuel injection that optimize fuel delivery for improved performance. The spacious cab design, complete with ergonomic seating and controls, ensures maximum operator comfort during long operating hours, promoting productivity.

In the case of the CZT2142, this model elevates the standard with its incorporate smart technology. It features real-time monitoring systems that provide critical data on engine performance, allowing for proactive maintenance and reduced downtime. The CZT2142 is also equipped with an advanced hydraulic system that provides exceptional lift capacity and versatility in attachment use, making it suitable for various farming applications.

All models feature cutting-edge safety technology, including rollover protection and enhanced visibility through strategically designed cab windows. The integration of telematics systems across these models allows for remote monitoring and diagnostics, further contributing to efficient fleet management.

Overall, the Axion ZT18533, ZT2142, and CZT2142 represent a comprehensive solution for modern agriculture. Their blend of power, efficiency, and advanced technology makes them indispensable tools for farmers looking to optimize their operations and enhance productivity in the field. With a focus on sustainability and innovation, these models are set to redefine the standards of agricultural machinery.