American Standard 754323-100 Rev A, American Standard bath Installation and Framing Instructions

INSTALLATION AND FRAMING INSTRUCTIONS:	FIGURE 1
The variety of installations possible for this combination system may require framing procedures	TYPICAL
	INSTALLATION
other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper,
plumb and square. Provisions must be made in all installations for an access opening for servicing
the air blower and controls. It is strongly recommended that an additional opening be provided for
access to the drain components. The apron should not be used as the primary access opening.

1.Position the combination system into the installation opening and level the deck in both directions, shimming the integral feet with attached baseboard as necessary. Refer to the Combination Installation Table for nominal installation dimensions. Mark the final position of

the underside of the deck by tracing a line on to the studs (see Figure 1). D

2. Remove the air massage system and attach a 1 x 4 stringer to the studs, with the top of the stringer touching the traced line.

!The rim of the bath must not support weight.

3.Install supplied cable drain components to the combination system according to the enclosed drain installation instructions. Before replacing your bath for final installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for suggested opening size (shadowed) and location dimensions. The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor.

4.Replace combination system and re-shim the integral support feet with attached baseboard, shimming the entire length of the baseboard as needed. Secure the shims using construction adhesive, silicone or equivalent materials.

!The rim of the bath must not support weight. Any finish material such as tile or wall board must be

self-supporting if it contacts the deck of the bath.

	TILE
	WALLBOARD
TILE	SEALANT
	BATH
BEAD
STRIP
	ADHESIVE
	LEVELING STRINGER
	1 x 4 (not for support)

NOTE: Tile bead kit not included and must be purchased separately.

COMBINATION INSTALLATION TABLE

DIM.

A

B

C

D

E

F

COMBINATION MODEL NUMBER

DESCRIPTION

2748

2742

2709**

3571

3572

3573

3574

3575

Nominal tub length recess opening

59-3/4"

1518mm

71-3/4"

1823mm

60-1/4"

1530mm

66-1/4"

1683mm

72-1/4"

1835mm

60"

1524mm

72-1/4"

1835mm

Nominal tub apron support opening

39-3/4"

1511mm

39-3/4"

1511mm

35"

889mm

35"

889mm

35"

889mm

40-3/4"

1035mm

41"

1041mm

Nominal tub width recess opening

41-3/4"

1060mm

41-3/4"

1060mm

36"

914mm

36"

914mm

36"

914mm

41-3/4"

1060mm

42"

1067mm

Nominal tub height opening

21"

533mm

20"

508mm

19-1/2"

495mm

19"

483mm

19"

483mm

19"

483mm

19"

483mm

19"

483mm

Nominal tub length cutout

58"

1473mm

70"

1778mm

67"

1702mm

58-1/2"

1486mm

64-1/2"

1638mm

70-1/2"

1791mm

58-1/4"

1480mm

70-1/2"

1791mm

Nominal tub width cutout

40-1/8"

1019mm

40-1/4"

1022mm

36-1/2"

927mm

34-1/2"

876mm

34-1/2"

876mm

34-1/2"

876mm

40-1/4"

1022mm

40-1/2"

1029mm

**USE CUTOUT TEMPLATE PROVIDED FOR 2709 MODEL

NOTICE:

DO NOT BUILD THE SURROUNDING STRUCTURE BEFORE RECEIVING YOUR AIR BATH. STRUCTURE MEASUREMENTS SHOULD BE VERIFIED AGAINST THE ACTUAL AIR BATH RECEIVED TO ENSURE PROPER FIT.

TYPICAL RECESS INSTALLATION

TYPICAL PIER TYPE INSTALLATION

AS DESIRED

F

CUTOUT

D

E

CUTOUT

D

A

NOTE:

FRONT EDGE

OF BATH MUST

BE SUPPORTED BY STUD WALL OR AMERICAN STANDARD APRON KIT

B	12
C	(305 mm)

LEVELING

STRINGERS24 (610 mm)

ACCESS PANEL MUST BE LOCATED

ON THE SAME SIDE AS THE BLOWER.

ALLOW OPEN FRAMING ON

BLOWER END FOR SERVICE.

AS DESIRED

MOUNTING

SURFACE

WATERPROOF SEALANT

BATH

12

(305 mm)

24

(610 mm)

ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON PUMP/MOTOR END FOR SERVICE.

UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

13 754323-100 Rev A