Meridian Audio 808.2I manual Important safety instructions, Safety warnings, To avoid overheating

Page 2

ii

Preface

Important safety instructions

•Read the instructions.

•Keep these instructions.

•Follow all instructions.

•Do not use this apparatus near water.

•Clean only with a dry cloth.

•Install only in accordance with the manufacturer’s instructions.

•Refer all servicing to approved service personnel.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

This apparatus has been designed with Class 1 construction and must be connected to a mains socket outlet with a protective earthing connection (the third grounding pin).

This apparatus uses a single-pole power switch. As a result it is not isolated from AC mains power when switched off at the rear panel. The apparatus may be isolated from mains power either by unplugging the power connector from the rear of the unit, or by unplugging the connector at the opposing end of the power cord or cable from its supply outlet. As a result, either or both of these connectors should remain accessible

Safety warnings

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE

•Do not expose the unit to dripping or splashing.

•Do not place any object filled with liquid, such as a vase, on the unit.

•Do not place naked flame sources, such as lighted candles, on the unit.

To avoid overheating

•Leave at least 10cm around the equipment to ensure sufficient ventilation.

Do not position the unit:

•In direct sunlight.

•Near heat sources, such as a radiator.

•Directly on top of heat producing equipment, such as a power amplifier.

To avoid interference

Do not position the unit:

•Near strong electrical or magnetic radiation, such as near a power amplifier.

Radio interference

FCC Warning: This equipment generates and can radiate radio frequency energy and if not installed and used correctly in accordance with our instructions may cause interference to radio communications or radio and television reception. It has been type-tested and complies with the limits set out in Subpart J, Part 15 of FCC rules for a Class B computing device. These limits are intended to provide reasonable protection against such interference in home installations.

EEC: This product has been designed and type-tested to comply with the limits set out in EN55013 and EN55020.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents 808.2/808.2i Signature Reference CD Player User Guide To avoid overheating Important safety instructionsSafety warnings To avoid interferenceContents Copyright and acknowledgements Sales and service in the UKSales and service in the USA Designed and manufactured in the UKIntroduction System integration Signal ProcessingIntegrated preamplifier Audio in and out SpecificationsDrive ControlsIntroduction Using the 808.2 Signature Reference CD Player Front panel keys Signature Reference CD PlayerMSR+ keys OFFTo switch to standby Switching on and offTo switch on from standby To insert a discTo restart the current track Playing a discTo play the disc To move to the next trackTo stop playback Stopping and pausing playTo continue after pausing To pause playbackRepeat To cancel A-B repeatTo cancel the repeat function To continuously repeat a disc1237 Scanning a discTo scan through a disc To make a selection by omitting tracks To choose a track to programmeTo make a selection by adding tracks To add or remove a track from a selection+ Phase Changing the absolute phaseTo display the phase setting To change the phase settingTo change the displayed information Changing the front-panel displayTo change the contrast or brightness Using Signature Reference CD Player Using the CD player preamplifier features Radio Selecting a sourceTo select a source To restore the sound Adjusting the system volumeTo change the volume To mute the soundBalance Changing the balanceTo change the balance Installing the CD player Unpacking Back panelCommunications connections Audio outputsAudio inputs 808.2i only Applications To connect to an analogue preamplifier Type 1 orSpeakerLink lead DSP loudspeaker Slave M5 lead To connect the 808.2/808.2i to a power amplifier Type 0 or Series, 500 Series, or 800 Series unit Configuring the CD player Type Choosing a standard settingTo select a standard setting To turn off Gain mode Setting up sourcesTo turn on Gain mode To adjust the sensitivity of a sourceConfiguring the CD Player Index Unpacking Volume, adjusting
Top Page Image Contents