Caldera Highland Series owner manual Operating Instructions

Page 13

OPERATING INSTRUCTIONS

SPA-SIDE CONTROL OPERATION

Your spa-side control panel consists of an LED display and convenient touch pads that allow you to set the water temperature and adjust the skim/filter cycle settings, as well as control the hydrotherapy jets, and light from

spa-side.

LED DISPLAY

The LED display on your spa-side control panel continually shows the spa’s actual water temperature. In certain situations, it will also display other messages. See TROUBLESHOOTING section.

TEMPERATURE CONTROL

The set temperature range is from 80°F (27°C) to 104°F (40°C). Higher temperatures can be reached which is indicated by one of these four settings: uT1,uT2, uT3, & uT4. These settings get progressively warmer, with uT4 the highest at approximately 107.5°F (42°C). (Temperatures of any

setting may rise slightly depending on the current use and condition of your spa, and on outside temperature.) To reach the u1-u4 temperature range, press the TEMP

▲button until 104°F (40°C) is displayed, then push down and hold the TEMP ▲ button for 5 seconds until the uT1 is illustrated.

The factory-set temperature is 102°F (39°C). Whenever power is disconnected and then reconnected to the spa, the water temperature will automatically seek this temperature, unless you set it otherwise using the temperature controls.

Pressing the TEMP ▲ button displays the spa’s set temperature. To increase the set temperature, press the TEMP ▲ button again, once for each degree of increased temperature desired. If you hold the button down, the set temperature will increase by one degree every half second. When the set temperature has been reached, the “READY” icon will diplay.

Pressing the TEMP ▼ button displays the spa’s set temperature. To decrease the set temperature, press the TEMP ▼ button again, once for each degree of decreased temperature desired. If you hold the button down, the set temperature will decrease by one degree every half second. When the set temperature has been reached, the “READY” icon will diplay.

JET PUMP CONTROL

Pressing the “JETS” button changes the jet pump functions, depending on the number of presses:

Olympia Spa Model only:

1st press:

Two-speed jet pump runs on low speed

2nd press:

Two-speed jet pump runs on high speed

3rd press:

One-and Two speed jet pumps run on high speed

4th press:

One-speed jet pump runs on high speed

5th press:

Both jet pumps are off.

Cumberland® & AventineTM Spas only:

1st press:

Two-speed jet pump runs on low speed

2nd press:

Two-speed jet pump runs on high speed

3rd press:

Jet pump off

•The pump on high speed automatically turns off after operating for one hour. The pump on low speed automatically turns off after operating for one hour.

•When the jets are active, the JETS icon on the control panel will illuminate.

LIGHT CONTROL

Your Highland spa is equipped with a blue LED light. Press the LIGHT button to turn it on. Press it a second and third time to dim the light to medium and low Press it a fourth time to turn it off. The light automically turns off after six hours. When the light is active, the LIGHT icon on the control panel will illuminate. For enhanced spa enjoyment, an optional six color wheel light feature is available to create your desired ambiance.

10

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Highland Series Welcome to the growing family of Caldera Spa owners WelcomeTable of Contents Important Safety Instructions Safety InformationAvoiding the Risk to Children DON’TUnclean water Health problems affected by spa useRisks to Avoid Avoiding the Risk of HyperthermiaImportant SPA Instructions InstallationSite and Selection Preparation Deck Installation Outdoor and Patio InstallationINDOOR/BASEMENT Installation SPA Cover InstallationVolt Installation Electrical InstallationElectrical Requirements and Precautions Selecting the Voltage for Your SPAPermanently Connected Volt Subpanel Wiring InstructionsOperation Notes START-UP and Refill ProceduresOlympia Model OLY SPA FeaturesCumberland Model CUH Operating Instructions Temperature Lock Lock FeaturesManual Clean Cycle Mystique LED Lighting OptionalGeneral Information Water Quality and MaintenanceWatkins SPA Water Maintenance Program Methods for Testing the SPA WaterBasic Chemical Safety HOW to ADD Chemicals to the WaterMaintaining the Sanitizer Level Balancing the Calcium Hardness CHIf the CH is too low add CH Increaser Ideal pH level for your spa water isMonarch Water Care System Monarch Silver ION Purifier Installation InstructionsChlorine Sodium Dichlor Silver ION Questions and AnswersDOS and DON’TS Super ChlorinationBuilding a Sanitizer Routine Supplemental Water MaintenanceMonarch Ozone System Optional Cleaning the Ozone InjectorPurewatertm Ozone System Optional Common Water Chemistry Questions Question Why can’t I fill my spa with soft water?Water Terminology Problem Probable causes Solutions Filter Maintenance MaintenanceFilter Cartridge Removal and Cleaning Care of the SPA PillowsCare of the Exterior Diverter Valve MaintenanceCare of the SPA Cover SPA ShellDraining Your SPA Wood SPA Cabinet Standard Optional on Olympia & CumberlandWinterizing Your SPA Acts Invalidating Warranty ServiceWatkins Customer Service DisclaimersGeneral Operation Troubleshooting Guide SPA TroubleshootingPage Page Page Highland Series SPA Specifications

Highland Series specifications

The Caldera Highland Series is an exceptional line of outdoor gear designed specifically for adventurers who seek the perfect blend of performance, comfort, and durability. Crafted with a deep understanding of the challenges faced in various environments, this series stands out for its innovative technologies and user-centric features.

One of the hallmark characteristics of the Caldera Highland Series is its use of advanced waterproof yet breathable materials. The outer fabric is engineered with a cutting-edge membrane that effectively repels water, keeping the user dry in unexpected downpours. Furthermore, this membrane allows moisture from within to escape, ensuring that wearers remain comfortable during intense physical activity. This feature is invaluable for those trekking through diverse climates, providing both protection and breathability.

In addition to weather resistance, the Highland Series includes an innovative insulation technology. Utilizing lightweight yet efficient insulation means that users can stay warm without the bulk associated with traditional outerwear. This is particularly important for those who prioritize both warmth and mobility during outdoor excursions. Designed for layering, the Highland Series garments fit seamlessly with other layers, enhancing versatility for various conditions.

Another notable aspect of the Caldera Highland Series is its attention to detail in design. The garments boast articulated joints and ergonomic cuts, allowing for an unrestricted range of motion. This design philosophy is particularly beneficial for climbers, hikers, and skiers who need gear that moves with them rather than against them.

Additionally, the series embraces sustainability, incorporating recycled and eco-friendly materials into its production processes. By prioritizing responsible manufacturing practices, Caldera not only focuses on performance but also on environmental stewardship, appealing to the growing number of eco-conscious consumers.

Finally, the Highland Series is equipped with strategic pocket placements and functional features such as adjustable hoods and cuffs, ensuring practicality without sacrificing style. With a focus on performance-driven functionality, durable craftsmanship, and a commitment to sustainability, the Caldera Highland Series offers outdoor enthusiasts a premier choice for their adventures, no matter where the journey leads. Whether hiking rugged trails or navigating snowy slopes, this series equips you with the reliability and comfort needed to conquer the great outdoors.
Top Page Image Contents