Cal Spas LTR20091002 manual Electronic Control Operation, Your Spa

Page 17

9800 Electronic Control Operation

Initial Start-up

When first powered up, your spa will perform a self-diagnostic check and then automatically go into priming mode. The topside will display PR to indicate this. Priming mode will be active for less than five minutes. When the spa has finished priming, the heater will be activated and the water temperature will be maintained in stan- dard mode. The spa will automatically heat to 100°F (37.5°C) at start-up until you change the set temperature as listed in the “Temperature Adjustment” section below.

17 Operating

These instructions will describe features and options that your particular spa may not be equipped with.

Temperature Adjustment

80°F - 104°F (26..0°C - 40..0°C)

The start-up temperature is set at 100°F (37.5°C). The last measured temperature is constantly displayed on the control panel. Note that the last measured spa temperature is displayed. The displayed temperature will be updated

when the pump has been running for at least two minutes.

Press the “UP” or “DOWN” buttons once to display the set temperature. Each time either button is pressed again, the set temperature will increase or decrease depending on which button is pressed. After three seconds, the control panel will automatically display the last measured spa temperature.

Time

When time hasn’t been programmed, the “TIME” icon flashes. To set the time, press the “TIME” button and then the “MODE/PROG” button. Use the “UP” and “DOWN” buttons to adjust time. See the next page for more detailed instructions.

Standard, Economy, Sleep, and Standby Modes

Mode/Prog: This button is used to switch between standard, economy, and sleep modes.

1.Press “MODE/PROG” to enter mode program- ming.

2.Press the “DOWN” button to cycle through to the desired mode.

3.Press “MODE/PROG” to confirm selection.

Standard Mode: This is programmed to maintain the desired temperature. Note that the last measured spa temperature displayed is current only when the pump has been running for at least two minutes. The “STAND” icon will display until the mode is changed.

Economy Mode: Economy mode heats the spa to the set temperature only during filter cycles. The “ECON”

2009 Inground Spas

icon will display until the mode is changed. Pressing the “JETS 1” button while in economy mode puts the spa in standard-in-economy mode, which operates the same as standard mode but reverts back to economy mode automatically after one hour. During this time, pressing the “MODE/PROG” button will revert to econ- omy mode immediately.

Sleep Mode: Sleep mode heats the spa to within 20°F (6.7°C) of the set temperature only during filter cycles. The “SLEEP” icon will display until the mode is changed.

Standby Mode: Pressing “Warm” or “Cool” then “JETS 2” will turn off all spa functions temporarily. This is helpful when changing a filter. Pressing any button resets the spa.

Jets 1 and Jets 2

Press the “JETS 1” button once to turn pump 1 on or off and to shift between low and high speeds if equipped. If left running, the low speed turns off af- ter two hours and the high speed turns off after 15 minutes. On non-circulation systems, the low speed of pump 1 runs when the blower or any other pump is on. It may also activate for at least two minutes every 30 minutes to detect the spa temperature and then to heat to the set temperature if needed, depending upon the mode. When the low speed turns on au- tomatically, it cannot be deactivated from the panel; however, the high speed may be started.

Option

This is an optional feature. Press the “OPTION” but- ton to turn the optional equipment on and off. If left

Your Spa

LTR20091002, Rev. B

www.calspas.com

Image 17
Contents LTR20091002, Rev. B 1/30/09 Preparing for Your New Inground Spa Clear Water Plan Cleaning and MaintenanceElectronic Control Operation AppendixHyperthermia Danger Important Safety InstructionsRead This First Preparing for Your New Inground Spa Inground Spa Installation ChecklistInground Spa ForYour NewPreparing forYour New Planning the Best Place for the Outdoor Equipment PackInground Spa Site Preparation SpaTesting the Gfci Breaker Gfci and Wiring RequirementsElectrical Requirements US and Canada ForYour New IngroundYour New Inground Spa Gfci Wiring DiagramRCD and Wiring Requirements Electrical Installation -- EuropeTesting the RCD Breaker Preparing forYour New IngroundRCD Wiring Diagram Preparing forYour New Inground Spa Installing the Inground ShellEquipment Pack Plumbing Connections Designer Spa SpecificationsPlumbing Connections Identifying Plumbing LinesGate/Slice Valves Air TestWater Test Remote Equipment Topside Control Panel Connecting Plumbing to Remote EquipmentElectrical and Electronic Con- nection See figure below Inground Spa Light Installation In- structionsYour New Inground Spa Pouring the Deck Your Spa Electronic Control OperationOperating SpaYour Message Frequency Action Required RPH Periodic Reminder MessagesRSA RCLMessage Meaning Action Required No message Diagnostic MessagesOn display DryStby Message Meaning Action RequiredSnb Sns Diverter Knobs Adjustable JetsWaterfalls Air VenturisClear Water Plan Contents of this sectionKey to Clear Water Clear Water PlanClear PlanWater Testing and Adjusting Spa WaterBalancing the Total Alkalinity Balancing the pHUsing Bromine as a Sanitizer Using Chlorine as a SanitizerSanitation Adding Sanitizer Tablets to the Chemical ChamberShocking the Water Chemical SafetyBather Load Filter CleaningClear Water PlanStarting the Spa with Fresh Water Maintenance Schedule Start Up Del Zone Eclipse OzonatorDay One Monday Day Two FridayProblem Probable Causes Possible Solutions Troubleshooting Water Clarity ProblemsSpa Cover Cleaning and MaintenanceRemoving and Reseating the Pillows Winterizing Cold Climate Draining Cleaning and Replacing the FilterDraining Your Spa Cleaning Cleaning the Cover, Shell and PillowsFast Sheen Spa finish protecting wax Appendix Replacement PartsFitness Series Exercise Program Keeping Fit with your Cal SpaConnecting the Exercise Equipment Cal Spas Chemicals LTR20091002, Rev. B 1/30/09