Check Safety Interlock System, Service Dealer

Maintenance

Figure 19

1.Spindle

2.Blade

3.Blade drive washer

4.Blade bolt washer assembly — Torque to 50-60 ft-lb (68-81 N-m) Apply lubricant to threads as needed to prevent seizing. Copper-based anti-seize preferable. Grease acceptable substitute.

B.Apply lubricant to the threads of the blade bolt as needed to prevent seizing. Copper based anti-seize is preferable. Grease is an acceptable substitute.

C.Install the blade drive washer and blade bolt washer assembly into the spindle. Make sure the hex in the washer is engaged on the spindle before tightening the bolt. Install blade bolt finger tight.

D.Place wrench on the top spindle nut then torque the blade bolts to 50-60 ft-lb (68-81 N-m).

WARNING

Incorrect installation of the blade or components used to retain the blade can be dangerous. Failure to use all original components and assembled as shown could allow a blade or blade component to be thrown out from under the deck resulting in serious personal injury or death.

Always install the original Exmark blades, blade bushings, and blade bolts as shown.

Check Safety Interlock System

Service Interval: Before each use or daily

Note: To prevent engine cut-outs on rough terrain the seat kill switch has a 1/2 second delay.

1.Check starting circuit. Starter should crank with, parking brake engaged, PTO disengaged and

motion control levers moved out in the neutral lock position. The operator does not need to be in the seat to start the engine.

Try to start with operator in seat, parking brake disengaged, PTO disengaged and motion control levers in the neutral lock position - starter must not crank.

Try to start with operator in seat, parking brake engaged, PTO engaged and motion control levers in the neutral lock position - starter must not crank.

Try to start with operator in seat, parking brake engaged, PTO disengaged, and the left motion control lever in, starter must not crank, repeat again with the right lever in, then with both levers in - starter must not crank.

2.Check the kill circuits. Run engine at one-third throttle, disengage parking brake and raise off of seat (but do not get off of machine) engine must initiate shutdown after approximately 1/2 second has elapsed (seat has time delay kill switch to prevent cut-outs on rough terrain).

Run engine at one-third throttle, engage PTO and raise off of seat (but do not get off of machine) engine must initiate shutdown after one second has elapsed if the handles are in. The delay will be 1/2 second if the handles are out.

Run engine at one-third throttle, with brake disengaged, move levers in and raise off seat (but do not get off of machine) engine must initiate shutdown after 1/2 second has elapsed.

Again, run engine at one-third throttle, brake engaged, and move left motion control lever in - engine must initiate shutdown after 1/2 second has elapsed.

Repeat again moving the right lever in, then moving both levers in - engine must initiate shutdown after 1/2 second has elapsed whether operator is on seat or not.

Note: If machine does not pass any of these tests, do not operate. Contact your authorized EXMARK

SERVICE DEALER.

Important: It is essential that operator safety mechanisms be connected and in proper operating condition prior to use for mowing.

00 & Higher, 850 specifications

The Exmark 850 is a top-of-the-line commercial mower, known for its durability, efficiency, and advanced features, making it a favorite among landscaping professionals. With a powerful engine and innovative technology, the Exmark 850 is designed to tackle tough mowing tasks while ensuring a high-quality cut.

One of the standout characteristics of the Exmark 850 is its robust engine performance. Powered by a reliable Kohler or Kawasaki engine, it delivers exceptional horsepower, enabling it to handle various terrains and grass types with ease. The engine is designed for fuel efficiency, allowing operators to work longer hours without frequent refueling, ultimately boosting productivity on the job.

The cutting deck of the Exmark 850 is engineered with precision, utilizing Exmark's proprietary UltraCut technology. This technology ensures that grass is cut evenly and efficiently, resulting in a clean, manicured appearance. The deck height is easily adjustable, allowing users to quickly change settings to accommodate different lawn conditions and preferences.

Another key feature is the innovative suspension system that enhances ride quality. The Exmark 850 is equipped with a heavy-duty front axle and high-performance suspension that absorbs bumps and uneven ground, allowing for a smoother mowing experience. This is especially beneficial for operators who spend long hours on the mower, reducing fatigue and improving comfort.

Ergonomics play a crucial role in the design of the Exmark 850. The operator station is thoughtfully crafted with optimal controls and comfortable seating, allowing for easy maneuverability and long-term use. The ergonomic handles and intuitive control layout make it easy for operators to navigate tricky landscapes, enhancing overall efficiency.

In terms of durability, the Exmark 850 is built to withstand the rigors of commercial use. The high-quality materials and construction ensure that this mower can handle challenging conditions, extending its lifespan and reducing maintenance needs. Additionally, Exmark offers an extensive warranty program, providing peace of mind for operators.

Safety features are also prioritized in the Exmark 850, with guards and shields designed to protect the operator while mowers are in use. These features also include emergency shut-off systems and blade brake systems, ensuring compliance with safety standards.

Overall, the Exmark 850 stands out as a high-performing, reliable, and efficient mower suitable for a variety of commercial landscaping tasks. With its powerful engine, advanced cutting technology, ergonomic design, and emphasis on durability and safety, it continues to be a top choice for professionals seeking high-quality lawn care equipment.