Exmark 00 & Higher, 850 manual Clean Engine and Exhaust System Area, Clean Hydro Fan Cooling Fins

Page 41

Maintenance

Cleaning

Clean Engine and Exhaust System Area

Service Interval: Before each use or daily (May be required more often in dry or dirty conditions.)

Removing debris from the hydro fan cooling fins will allow the hydro system to run cooler and improve the life of the hydro system.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lift the seat to access the LH and RH hydro drive area.

3.Remove accumulated debris from the hydro fan cooling fins.

CAUTION

Excessive debris around engine cooling air intake and exhaust system area can cause engine, exhaust area, and hydraulic system to overheat which can create a fire hazard.

Clean all debris from engine and exhaust system area.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Clean all debris from rotating engine air intake screen, around engine shrouding, and exhaust system area.

3.Wipe up any excessive grease or oil around the engine and exhaust system area.

Remove Engine Shrouds and Clean Cooling Fins

Service Interval: Every 100 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Remove cooling shrouds from engine and clean cooling fins. Also clean dust, dirt and oil from external surfaces of engine which can cause inadequate cooling.

3.Make sure cooling shrouds are reinstalled. Operating the engine without cooling shrouds will cause engine damage due to overheating.

Clean Hydro Fan Cooling Fins

Service Interval: Before each use or daily

Clean Debris From Machine

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Clean off any oil, debris, or grass build-up on the machine and cutting deck, especially under deck belt shields, around the fuel tank, around engine and exhaust area.

Clean Grass Build-Up Under Deck

Service Interval: Before each use or daily

1.Park the machine on a level surface and disengage the blade control switch.

2.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

3.Raise deck to the transport (5 inch (12.7 cm) cutting height) position. Lift the front of unit and support unit using jack stands or equivalent support.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

4.Clean out any grass build-up from underside of deck and in discharge deflector.

41

Image 41
Contents Quest SP Models California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices PreparationSafety Operation Slope Operation Using the Rollover Protection System RopsTowing Maintenance and StorageChildren Safety Safety and Instructional Decals 103-3270 107-2102 109-3148 109-6014 109-9173 112-8651 PTO Switch Symbols 116-2834 Systems SpecificationsModel Numbers Dimensions Product Overview Curb WeightTorque Requirements Tread Width Center to Center of Tires, WidthwiseControls OperationFuel Shut-Off Valve Drive Wheel Release ValvesHour Meter Pre-Start PTO Engagement SwitchDeck Lift Pedal Transport LockRaise the Rollover Protection System Rops Operating InstructionsStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTODriving the Machine Adjusting the Cutting HeightTorque the 3/8 nyloc nut to 27-33 ft-lb 37-45 N-m Adjusting the Anti-Scalp RollersLoading a Unit TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Do Not jump start a weak battery if these conditions existService Dealer Check Safety Interlock SystemCheck Rollover Protection System Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Check Spark PlugsCheck Spark Arrester if equipped Copper-Based Anti-seize Thread Locking AdhesivesDielectric Grease Deck LevelingAdjusting the Blade Slope Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Adjusting the height Motion Control Handle AdjustmentElectric Clutch Adjustment Full Forward Tracking AdjustmentAdjusting the Seat Ride Suspension Feeler gauge Brake mounting bolt Shim Remove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Fins Clean Debris From MachineMotor Oil Disposal Battery DisposalWaste Disposal Problem Possible Cause Corrective Action TroubleshootingPosition see Drive Wheel Release Electrical Diagram SchematicsSchematic Quest SP Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 44 pages 57.61 Kb Manual 32 pages 16.59 Kb Manual 28 pages 32.2 Kb Manual 60 pages 29.4 Kb Manual 24 pages 21.56 Kb Manual 48 pages 5.05 Kb Manual 40 pages 46.04 Kb

00 & Higher, 850 specifications

The Exmark 850 is a top-of-the-line commercial mower, known for its durability, efficiency, and advanced features, making it a favorite among landscaping professionals. With a powerful engine and innovative technology, the Exmark 850 is designed to tackle tough mowing tasks while ensuring a high-quality cut.

One of the standout characteristics of the Exmark 850 is its robust engine performance. Powered by a reliable Kohler or Kawasaki engine, it delivers exceptional horsepower, enabling it to handle various terrains and grass types with ease. The engine is designed for fuel efficiency, allowing operators to work longer hours without frequent refueling, ultimately boosting productivity on the job.

The cutting deck of the Exmark 850 is engineered with precision, utilizing Exmark's proprietary UltraCut technology. This technology ensures that grass is cut evenly and efficiently, resulting in a clean, manicured appearance. The deck height is easily adjustable, allowing users to quickly change settings to accommodate different lawn conditions and preferences.

Another key feature is the innovative suspension system that enhances ride quality. The Exmark 850 is equipped with a heavy-duty front axle and high-performance suspension that absorbs bumps and uneven ground, allowing for a smoother mowing experience. This is especially beneficial for operators who spend long hours on the mower, reducing fatigue and improving comfort.

Ergonomics play a crucial role in the design of the Exmark 850. The operator station is thoughtfully crafted with optimal controls and comfortable seating, allowing for easy maneuverability and long-term use. The ergonomic handles and intuitive control layout make it easy for operators to navigate tricky landscapes, enhancing overall efficiency.

In terms of durability, the Exmark 850 is built to withstand the rigors of commercial use. The high-quality materials and construction ensure that this mower can handle challenging conditions, extending its lifespan and reducing maintenance needs. Additionally, Exmark offers an extensive warranty program, providing peace of mind for operators.

Safety features are also prioritized in the Exmark 850, with guards and shields designed to protect the operator while mowers are in use. These features also include emergency shut-off systems and blade brake systems, ensuring compliance with safety standards.

Overall, the Exmark 850 stands out as a high-performing, reliable, and efficient mower suitable for a variety of commercial landscaping tasks. With its powerful engine, advanced cutting technology, ergonomic design, and emphasis on durability and safety, it continues to be a top choice for professionals seeking high-quality lawn care equipment.