Exmark 4500-686 Rev. B manual Check for Loose Hardware

Page 25

Maintenance

Figure 23

1. Inner cutting edge radius 2. Cutting angle

C.Check the balance of the blade by placing the center hole of the blade over a nail or screwdriver shank clamped horizontally in a vise (Figure 24). If either end of the blade rotates downward, file that end (not the cutting edge). The blade is properly balanced when neither end drops.

Figure 24

1. Blade

3. Screwdriver

2.Vise

D.For Installation: Make sure to grasp the end of the blade using a rag or a thickly padded glove.

For Blade Brake Clutch Units: Install a sharp, balanced Exmark blade, blade support, and the blade nuts. The sail of the blade must point toward the top of the lawn mower housing for proper installation. Torque the blade nuts to 23-27 ft-lb (31-37 N m).

For Units without a Blade Brake Clutch: Install a sharp, balanced Exmark blade, blade support, and blade bolt. The sail of the blade must point toward the top of the lawn mower housing for proper installation. Torque the blade bolt to 35-45 ft-lb (47-61 N m).

Figure 25

1.Blade Brake Clutch Units

2.Units without a Blade Brake Clutch

6.Return the lawn mower to its upright position.

7.Connect the wire to the spark plug.

Check for Loose Hardware

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop.

2.Visually inspect machine for any loose hardware or any other possible problem. Tighten hardware or correct the problem before operating.

Check the Blade Brake

Clutch Bail Operation (Blade

Brake Clutch Units Only)

Service Interval: Before each use or daily

Check the Blade Brake Clutch (BBC) bail operation for any operation problems or deteriorating components, such as the spring. Replace components or correct any problems before operating. Refer to Operating the Blade Control Lever in Operation.

25

Image 25
Contents Commercial California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Operation Slope Operation Maintenance and StorageSafety and Instructional Decals 109-9317 116-1922 116-2685 117-2718 116-1900 116-2737 Dimensions SpecificationsModel Numbers SystemsOperation Product OverviewControls Blade Control BailThrottle-Choke Lever ECXHN21 Engine Stop SwitchChoke Control ECXHNBBC21 Blade Control Lock Lever Blade Brake Clutch Units OnlyPre-Start Handle AdjustmentOperating Instructions Starting the Engine Open the Fuel Shut-Off ValveStopping the Engine Using the Mulch PlugAuthorized Service Dealer Adjusting the Cutting Height Test Using the Grass BagUsing the Grass Bag Operating Tips Recommended Maintenance Schedules MaintenanceChecking the Blade Brake Clutch Blade Brake Clutch Only Check Engine Oil LevelCheck the Mower Blade Emptying the Fuel Tank and Cleaning the Fuel Filter sectionCheck for Loose Hardware Service Air Filter ECSHN21 Units Service Air Filter Kawasaki UnitsDamaged or excessively dirty Service Air Filter ECXHNBBC21 and ECXHN21 UnitsChange Engine Oil Change Oil Filter ECXKA21 and ECXKABBC21 Emptying the Fuel Tank and Cleaning the Fuel FilterCheck Condition Of Belt Self-Propelled Units Only Check Spark PlugsAdjusting the Self-Propel Drive Self-Propelled Units Only AdjustmentsAdjustment of drive cable nuts Cleaning the Discharge Tunnel and Plug Clean Grass Build-Up Under DeckCleaning Under the Belt Cover Self-Propelled Units Only Screws BBC Shield Motor Oil Disposal Waste DisposalPreparing the Fuel System StoragePreparing the Engine General Storage InformationProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Exmark Commercial Turf Equipment Page See EXMARK’S Complete Line of Accessories and Options

4500-686 Rev. B specifications

The Exmark 4500-686 Rev. B is a cutting-edge commercial mower that embodies the perfect blend of performance, durability, and user-friendly features. Designed for professional landscapers and grounds maintenance professionals, this mower is built to handle the rigorous demands of large properties and commercial applications.

One of the standout features of the Exmark 4500-686 Rev. B is its powerful engine. Equipped with a robust EFI (Electronic Fuel Injection) engine, it delivers exceptional power and fuel efficiency. The engine's advanced technology allows for quicker starts and better throttle response, ensuring that users can tackle their mowing tasks without any delays. This efficiency translates into reduced operating costs and less time spent refueling.

Another notable technology integrated into this mower is the UltraCut deck system. The 4500-686 Rev. B features a precision-engineered cutting deck that provides a superior cutting performance, offering an even and professional finish to any lawn. The design promotes optimal airflow beneath the deck, resulting in better grass lift and dispersion, which reduces clumping and enhances the quality of the cut. Additionally, the cutting height is easily adjustable, allowing operators to customize their mowing according to specific turf conditions.

User comfort is a paramount consideration in the design of the Exmark 4500-686 Rev. B. The mower is equipped with an ergonomic seat and controls that minimize operator fatigue during extended use. The full-suspension seat absorbs shocks and vibrations, while the easy-to-use controls allow for intuitive operation, ensuring that mowing is a seamless and productive experience.

Durability is another key characteristic of the 4500-686 Rev. B. Built with high-quality materials and components, this mower is designed to withstand the wear and tear of everyday use. The frame is reinforced to provide added strength, while the corrosion-resistant coating ensures that it maintains its appearance and functionality over time.

In conclusion, the Exmark 4500-686 Rev. B is an exceptional choice for anyone looking for a reliable and efficient commercial mower. With its powerful EFI engine, advanced cutting technologies, emphasis on operator comfort, and rugged build quality, this mower offers unmatched performance in the field. Whether for professional landscaping or maintaining large properties, the Exmark 4500-686 Rev. B is engineered to meet the demands of any mowing job.