Hayter Mowers RZT420H manual Cleaning and Storage

Page 43

Storage

Cleaning and Storage

1.Disengage the blade control switch, move the motion controls outward to the park position, stop the engine, and remove the key.

2.Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine. Clean dirt and chaff from the outside of the engine cylinder head fins and blower housing.

Important: You can wash the machine with mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water, especially near the control panel, engine, hydraulic pumps, and motors.

3.Service the air cleaner; refer to Servicing the Air Cleaner in the Engine Maintenance section.

4.Grease and oil the machine; refer to the Lubrication section.

5.Change the crankcase oil and filter; refer to Servicing the Engine Oil in the Engine Maintenance section.

6.Check the tyre pressure; refer to Checking the Tyre Pressure in the Drive System Maintenance section.

7.Charge the battery; refer to Servicing the Battery in the Electrical System Maintenance section.

8.Check the condition of the blades; refer to Servicing the Cutting Blades in the Cutter Deck Maintenance section.

9.Prepare the machine for storage when non-use occurs over 30 days. Prepare the machine for storage as follows.

10.Add a petroleum based stabilizer/conditioner to the fuel in the tank. Follow the mixing instructions from the stabilizer manufacturer. Do not use an alcohol based stabilizer (ethanol or methanol).

Note: A fuel stabilizer/conditioner is most effective when mixed with fresh petrol and used at all times.

Run the engine to distribute the conditioned fuel through the fuel system (5 minutes).

Stop the engine, allow it to cool, and drain the fuel tank; refer to Draining the Fuel Tank in the Fuel System Maintenance section.

Restart the engine and run it until it stops.

Choke the engine. Start and run the engine until it will not start.

Dispose of fuel properly. Recycle pursuant to local codes.

Important: Do not store stabilizer/conditioned petrol over 30 days.

11.Remove the spark plug(s) and check its condition; refer to Servicing the Spark Plug in the Engine Maintenance section. With the spark plug(s) removed from the engine, pour two tablespoons of engine oil into the spark plug hole. Use the starter to crank the engine and distribute the oil inside the cylinder. Install the spark plug(s). Do not install the wire on the spark plug(s).

12.Clean any dirt and chaff from the top of the cutter deck.

13.Scrape any heavy buildup of grass and dirt from the underside of the cutter deck, then wash the cutter deck with a garden hose.

14.Check the condition of the drive and cutter deck belts.

15.Check and tighten all bolts, nuts, and screws. Repair or replace any part that is worn or damaged.

16.Paint all scratched or bare metal surfaces. Paint is available from your Authorized Service Dealer.

17.Store the machine in a clean, dry garage or storage area. Remove the key from the ignition switch and keep it in a memorable place. Cover the machine to protect it and keep it clean.

43

Image 43
Contents With Recycling/Side Discharge Deck RZT420H Ride-OnIntroduction ContentsSafe Operating Practices SafetyTraining Operation PreparationVibration Turn Riding Mower SafetySound Power Sound PressureSlope Chart 93-7009 106-8717 Safety and Instructional Decals110-6824 Battery Symbols Loose Parts SetupSetting Up the Motion Control Levers No Parts Required ProcedurePage Connecting the Battery Installing the Seat CableParts needed for this procedure Checking the Tyre Pressure Completing the SetupProduct Overview Controls Operation Think Safety FirstRecommended Fuel Filling the Fuel Tank Using Stabilizer/ConditionerStarting the Engine Checking the Engine Oil LevelEngaging the Blades Safety Interlock SystemOperating the Blades Stopping the EngineForward Testing the Safety Interlock SystemDriving Forward or Backward Stopping the MachinePositioning the Seat Adjusting the Height of CutAdjusting the Motion Control Levers Adjusting the HeightTo Push the Machine Adjusting the TiltPushing the Machine by Hand Side DischargeInstalling the Discharge Cover for Mulching Removing and Installing the Discharge CoverRemoving the Discharge Cover for Side Discharge Operating Tips Recommended Maintenance Schedules MaintenanceRaising the Seat Premaintenance ProceduresAccessing the Engine Accessing the BatteryGreasing the Bearings LubricationServicing the Air Cleaner Engine MaintenanceServicing Paper Element Checking the Oil Level Servicing the Engine OilChanging the Oil and the Filter Oil drain hose Removing the Spark Plug Cleaning the Blower HousingInstalling the Spark Plug Servicing the Spark PlugReplacing the Fuel Filter Fuel System MaintenanceCharging the Battery Electrical System MaintenanceRemoving the Battery Installing the Battery Charging the BatteryServicing the Fuses Checking the Tyre Pressure Drive System MaintenanceInspecting the Blades Cutter Deck MaintenanceServicing the Cutting Blades Before Inspecting or Servicing the BladesSharpening the Blades Installing the BladesLeveling the Cutter Deck from Side-to-Side Removing the BladesAdjusting the Front-to-Rear Blade Slope Removing the Cutter Deck Replacing the Cutter Deck Belt Cutter Deck Belt MaintenanceInstalling the Cutter Deck Inspecting the BeltsReplacing the Grass Deflector Washing the Underside of the Cutter Deck CleaningStorage Cleaning and StorageProblem Possible Cause Corrective Action TroubleshootingProblem Possible Cause Corrective Action Schematics Page Page 1st Year 12 months Page Limited Warranty Date of Sale Your Local Dealer

RZT420H specifications

The Hayter Mowers RZT420H is a cutting-edge lawn mower designed for those who demand efficiency and superior performance while maintaining their gardens. This machine combines innovative technology with user-friendly features to deliver a top-notch mowing experience.

One of the standout features of the RZT420H is its robust 42-inch cutting deck, ideally suited for medium to large lawns. This size allows for swift mowing while ensuring a clean and even cut. The cutting deck is made from high-quality materials, providing durability and resistance against wear and tear. Additionally, the deck’s design is optimized for excellent airflow, enhancing the cutting and mulching performance.

Powering the RZT420H is a reliable 20 HP Kohler engine. This engine provides ample power to handle tough grass conditions, ensuring that you can mow through dense areas without bogging down. The hydrostatic transmission allows for smooth, effortless speed changes, giving users precise control over their mowing speed. Whether navigating tight corners or tackling open fields, the hydrostatic system ensures a seamless mowing experience.

A significant advancement in the RZT420H is its zero-turn capability. This feature enables the mower to pivot around obstacles with ease, reducing the time spent trimming and maneuvering. This agility is complemented by a comfortable operator station, which includes an adjustable seat and user-friendly controls, ensuring that mowing is a pleasurable activity rather than a chore.

The RZT420H is also equipped with a range of convenience features. The easy-to-access maintenance points simplify routine care, making it easier to keep the mower in optimal working condition. Additionally, the mulching kit allows for effective grass recycling, returning nutrients to the lawn while minimizing yard waste.

Furthermore, the RZT420H boasts a compact design, which is particularly advantageous for storage and transport. Its exceptional build quality, combined with cutting-edge technology and thoughtful design details, makes the Hayter Mowers RZT420H a remarkable choice for homeowners seeking a reliable and efficient lawn maintenance solution. In conclusion, this mower brings together power, precision, and convenience, making it a worthy investment for any lawn care enthusiast.