Husqvarna 137, 142 Cutting Methods, Chain Brake, Important Points, Tree Felling Techniques

Page 9

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0,5 mm thick. Repairs on a chain brake should be made by an authorized service dealer. Take your unit to the place of pur- chase if purchased from a servicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

S When cutting with the saw, the chain brake

must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION: The chain brake must be checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14” (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS

SCheck chain tension before first use and af- ter 1 minute of operation. See CHAIN TEN-

SION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign ob- ject. Inspect the saw and repair or replace parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain

and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of using your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or engine can result.

S Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. If you run the saw at full throttle with- out a cutting load, unnecessary wear can

occur to the chain, bar, and engine.

STo avoid losing control when cut is com- plete, do not put pressure on saw at end

of cut.

SStop the engine before setting the saw down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near build- ings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be ale to see well, nor during bad weather such as rain, snow, or strong winds, etc. If the tree makes contact with any utility line, the utility company should be notified im- mediately.

SCarefully plan your sawing operation in ad- vance.

SClear the work area. You need a clear area all around the tree so you can have secure footing.

SThe chain saw operator should keep on

the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled.

SStudy the natural conditions that can cause the tree to fall in a particular direction.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Français EnglishDeutsch EspañolIdentification of Symbols Identification What is WHAT?Plan Ahead Safety RulesOperate Your SAW Safely Maintain Your SAW in Good Working OrderReduce the Chance Kickback KickbackMaintain Control Refuel unitChain Brake Kickback Safety FeaturesAssembly Attaching the Optional Bumper SpikeAttaching the BAR & Chain If not Chain Tension Including units with chain already installed Fueling & LubricationFueling Engine BAR and Chain Lubrication StartingImportant Points to Remember Starting a Warm EngineChain Brake Cutting MethodsImportant Points Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Inches in diameter or largerTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsCarburetor Adjustment ServiceLimbing PruningChain Sharpening BAR MaintenanceIgnition Timing Spark PlugTroubleshooting Table Cause Remedy Load Adjustment EngineEmpty fuel tank and refill with Relating to 2000/14/EC Declaration of ConformityTechnical Data Sheet

137, 142 specifications

The Husqvarna 137 and 142 are popular chainsaw models known for their reliability and performance, catering to both residential and light professional use. Bringing together a blend of innovative technologies and user-friendly features, these models have been designed to ensure that tasks such as tree pruning, firewood cutting, and light felling can be conducted efficiently and safely.

One of the standout features of both the Husqvarna 137 and 142 is their lightweight construction. Weighing in at approximately 4.5 kg, these chainsaws are easy to handle, particularly for users who may need to work for extended periods. This lightweight design significantly reduces fatigue, enabling operators to work longer without the weariness often associated with heavy machinery.

Powering these chainsaws is a robust 2.0 kW engine, which delivers an optimal balance of performance and efficiency. The engine has been engineered to provide a fast and consistent chain speed, allowing for clean and precise cuts. An efficient air filtration system contributes to the longevity of the engine, ensuring less frequent cleaning and maintenance. This feature is particularly advantageous for users who rely on their equipment for frequent tasks.

Both models come equipped with an automatic oil pump that ensures proper lubrication of the chain and bar during operation. This feature not only extends the life of the chainsaw but also enhances cutting efficiency. Additionally, the chain tensioning system is designed for easy adjustments, providing users with the ability to maintain the proper tension with minimal effort.

Safety is also a key consideration in the design of the Husqvarna 137 and 142. These models feature a chain brake that effectively stops the chain's movement in the event of kickback, protecting the operator from potential injury. Furthermore, the anti-vibration technology integrated into the handles helps to reduce vibrations felt by the user, contributing to a more comfortable and safer operating experience.

The ergonomic design is complemented by an intuitive layout, with controls that are easy to access and operate. The combination of performance, safety features, and user-centric design makes the Husqvarna 137 and 142 excellent choices for anyone needing a dependable chainsaw for various tasks. These models offer a powerful, efficient, and comfortable experience, making them an ideal investment for both hobbyists and occasional users alike.
Top Page Image Contents