Husqvarna 14 Pro manual Storage, Winter storage, Service

Page 42

STORAGE

Winter storage

At the end of the season the machine should immediately be put in order for storage, also if it is going to stand idle for more than 30 days. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine.

Fuel stabiliser is an acceptable alternative to avoid tacky deposits during storage. If alkylate petrol (Aspen) is used stabiliser is not necessary since this fuel is stable. However, one should avoid changing from standard to alkylate petrol since sensitive rubber parts can harden. Add stabiliser to the fuel in the tank or the storage container. Always use the mixing ratios indicated by the manufacturer. Run the engine for at least 10 minutes after adding the stabiliser so that it will reach the carburettor. Do not empty the fuel tank and carburettor if stabiliser has been added.

!WARNING!

Never place an engine with fuel in the tank indoors or in poorly ventilated areas where petrol fumes can come into contact with naked flames, sparks or pilot flames in boilers, hot water heaters, or drying cabinets, etc. It is highly inflammable and negligent usage can cause severe person injury and material damage. Drain off the fuel in an approved container outdoors and well clear of naked flames. Never use petrol for cleaning purposes. Use degreasing agents and hot water instead.

To put the machine in order for storage follow these instructions:

1.Carefully clean the machine, especially under the cutting unit. Touch-up paint damage to avoid rust.

2.Inspect the machine for worn or damaged parts and tighten loose screws and nuts.

3.Change the oil, and take care of the waste oil.

4.Empty the fuel tank. Start the engine and run it until the carburettor is emptied of fuel.

5.Remove the plugs and pour in a tablespoon of engine oil in each cylinder. Pull round the engine to distribute the oil and screw the plugs back on.

6.Grease all grease nipples, joints and axles.

7.Remove the battery. Clean it, charge it, and store it in a cool place. Protect the battery from low temperatures (below freezing point).

8.Store the machine in a clean and dry place and cover it over for extra protection.

Service

When ordering spare parts state the purchase year, model, type, and serial number.

Always use genuine parts.

Annual inspection or trimming by an authorised service workshop is a good way of getting the best out of your machine the next season.

40 – English

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Rider 14 Pro 101 90Svenska Contents General operation Safety InstructionsSafe operation practices for ride-on mowers II. Slope operationTowing IV. ServiceTravel and transport on public roads Intended useExplanation of Symbols Read the instructionsGeneral use Driving on slopes Do as followsMaintenance ChildrenNever smoke in the vicinity of the battery or Presentation Presentation10 1112 13 Location of the controls Throttle control Choke leverSpeed limiter Cutting unit Lift lever for cutting unitSeat Lever for adjustment of the cutting heightParking brake FuellingDriving Before startingStarting the engine Driving the machine Cutting tips Stopping the engine Disengage leverMaintenance Maintenance scheduleFront hood Removing of the machine hoodsEngine hood Right-hand fenderCheck the engine’s oil level Check the engine’s cooling air intakeChecking of the fuel pump’s air filter Check the transmission’s air intake Check the transmission’s oil levelChecking and adjustment of the steering wires Check the safety system Adjusting the brakesCheck the level of the battery acid Poorly adjusted brakes can result in reduced braking powerDo not use compressed air to clean the paper filter Replacing the air filterFitting the cutting unit Installing BioClip Adjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismRemoving the cutting unit Removing the belt Belt replacement on the BioClip Replacing the cutting unit’s beltsBelt replacement on BioClip Service position for cutting unit Placing in service positionMaintenance Restoring from service position Checking the blades Changing the oil General lubrication Replacement of the oil filterLubrication Lubrication of front wheel bearingsChecking and adjustment of the throttle wire Checking the tyre pressureReplacement of the fuel filter Cleaning the filterMuffler air intake Trouble Shooting Schedule Problem ProcedureService StorageWinter storage Wiring Diagram Technical Data Rider 14 ProBioClip Side ejector Rear ejector«*3%5¬ Page 2000W02

14 Pro specifications

The Husqvarna 14 Pro is a reliable and powerful cutting instrument utilized primarily in professional applications. Designed with the heavy-duty user in mind, this saw exemplifies efficiency and durability, making it an essential tool for construction and woodworking professionals.

One of the main features of the Husqvarna 14 Pro is its robust engine, which boasted a high power-to-weight ratio. With its advanced two-stroke engine technology, it provides excellent performance while maintaining lower fuel consumption and emissions. The efficient engine is designed for optimal power delivery, ensuring that the user can tackle the toughest cutting tasks with confidence.

The 14 Pro features a 14-inch cutting blade, allowing users to make precise cuts through a variety of materials, including concrete, asphalt, and masonry. The blade's design contributes to both improved performance and longevity, making it a cost-effective choice for professionals who rely on dependable tools to complete their projects on time.

One of the standout technologies integrated into the Husqvarna 14 Pro is the Active Air Filtration system. This innovative feature ensures that the engine is well-protected from contaminants, extending the lifespan of the saw and maintaining peak performance. Alongside this system is the Wet Cutting Kit option, which allows for wet cutting applications to minimize dust and improve cut quality.

Ergonomics play a significant role in the design of the Husqvarna 14 Pro. The saw comes equipped with adjustable handles, ensuring that professionals can work comfortably for extended periods. The lightweight design also contributes to reduced user fatigue, allowing for more efficient operation throughout the day.

Safety is another vital aspect of the Husqvarna 14 Pro. The saw is equipped with several safety features, including a protective guard and an emergency stop button. These features provide peace of mind to users, assuring them that they can operate the tool with minimized risk.

In summary, the Husqvarna 14 Pro stands out in the category of cutting saws due to its powerful engine, advanced filtration technology, precision cutting capabilities, ergonomic design, and robust safety features. Ideal for professionals in construction and masonry, the Husqvarna 14 Pro is designed not just to meet but to exceed the expectations of demanding users, marking it as a trusted ally in heavy-duty applications.
Top Page Image Contents