Husqvarna 14 Pro manual Changing the oil

Page 37

MAINTENANCE

Changing the oil

The oil should be changed for the first time after 8 hours of running time. Thereafter it should be changed every 50 hours of running time. If the engine is run hard or during high temperatures the oil should be changed every 25 running hours.

!WARNING!

Engine oil can be very hot if it is drained off directly after the engine is stopped. Therefore allow the engine to cool down first.

1. Dismantle the engine hood as described on page 18.

2. Place a receptacle under the engine’s drain plug.

3.Remove the dip stick. Remove the drain plug on the left-hand side of the engine.

4.Let the oil run out into the receptacle.

5.Fit the oil plug and tighten well.

6.Fill up with oil to the FULL mark on the dip stick. Use engine oil SAE 30 or SAE 10W-30, class CD–CF (over 0°). Use engine oil SAE 5W-30, class CD–CF (below 0°). The total oil volume in the engine is 1,5 litres.

7.Run the engine warm and then check that there is no leakage from the oil plug.

The oil is filled in the same hole as the dip stick.

IMPORTANT INFORMATION

Used engine oil is hazardous to health and must by law not be poured out on the ground or in the nature, but shall be handed in to a workshop or special environmental station. Avoid skin contact, wash with soap and water in the event of spillage.

 

ADD

FULL

ADD

FULL

 

English – 35

Page 36 Page 38
Image 37
Page 36 Page 38
Contents 101 90 Rider 14 ProSvenska Contents Safe operation practices for ride-on mowers Safety InstructionsGeneral operation II. Slope operationTravel and transport on public roads IV. ServiceTowing Intended useRead the instructions Explanation of SymbolsGeneral use Do as follows Driving on slopesChildren MaintenanceNever smoke in the vicinity of the battery or Presentation Presentation10 1112 13 Location of the controls Choke lever Throttle controlSpeed limiter Lift lever for cutting unit Cutting unitParking brake Lever for adjustment of the cutting heightSeat FuellingBefore starting DrivingStarting the engine Driving the machine Cutting tips Disengage lever Stopping the engineMaintenance schedule MaintenanceEngine hood Removing of the machine hoodsFront hood Right-hand fenderCheck the engine’s cooling air intake Check the engine’s oil levelChecking of the fuel pump’s air filter Check the transmission’s oil level Check the transmission’s air intakeChecking and adjustment of the steering wires Check the level of the battery acid Adjusting the brakesCheck the safety system Poorly adjusted brakes can result in reduced braking powerReplacing the air filter Do not use compressed air to clean the paper filterFitting the cutting unit Installing BioClip Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitRemoving the cutting unit Removing the belt Replacing the cutting unit’s belts Belt replacement on the BioClipBelt replacement on BioClip Placing in service position Service position for cutting unitMaintenance Restoring from service position Checking the blades Changing the oil Lubrication Replacement of the oil filterGeneral lubrication Lubrication of front wheel bearingsChecking the tyre pressure Checking and adjustment of the throttle wireCleaning the filter Replacement of the fuel filterMuffler air intake Problem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage Wiring Diagram Rider 14 Pro Technical DataSide ejector Rear ejector BioClip«*3%5¬ Page 2000W02

14 Pro specifications

The Husqvarna 14 Pro is a reliable and powerful cutting instrument utilized primarily in professional applications. Designed with the heavy-duty user in mind, this saw exemplifies efficiency and durability, making it an essential tool for construction and woodworking professionals.

One of the main features of the Husqvarna 14 Pro is its robust engine, which boasted a high power-to-weight ratio. With its advanced two-stroke engine technology, it provides excellent performance while maintaining lower fuel consumption and emissions. The efficient engine is designed for optimal power delivery, ensuring that the user can tackle the toughest cutting tasks with confidence.

The 14 Pro features a 14-inch cutting blade, allowing users to make precise cuts through a variety of materials, including concrete, asphalt, and masonry. The blade's design contributes to both improved performance and longevity, making it a cost-effective choice for professionals who rely on dependable tools to complete their projects on time.

One of the standout technologies integrated into the Husqvarna 14 Pro is the Active Air Filtration system. This innovative feature ensures that the engine is well-protected from contaminants, extending the lifespan of the saw and maintaining peak performance. Alongside this system is the Wet Cutting Kit option, which allows for wet cutting applications to minimize dust and improve cut quality.

Ergonomics play a significant role in the design of the Husqvarna 14 Pro. The saw comes equipped with adjustable handles, ensuring that professionals can work comfortably for extended periods. The lightweight design also contributes to reduced user fatigue, allowing for more efficient operation throughout the day.

Safety is another vital aspect of the Husqvarna 14 Pro. The saw is equipped with several safety features, including a protective guard and an emergency stop button. These features provide peace of mind to users, assuring them that they can operate the tool with minimized risk.

In summary, the Husqvarna 14 Pro stands out in the category of cutting saws due to its powerful engine, advanced filtration technology, precision cutting capabilities, ergonomic design, and robust safety features. Ideal for professionals in construction and masonry, the Husqvarna 14 Pro is designed not just to meet but to exceed the expectations of demanding users, marking it as a trusted ally in heavy-duty applications.
Top Page Image Contents