Husqvarna 14 Pro manual IV. Service, Travel and transport on public roads, Towing, Intended use

Page 5

SAFETY INSTRUCTIONS

IV. Service

1.Use extra care in handling gasoline and other fuels. They are flammable and vapours are explosive.

a)Use only an approved container.

b)Never remove gas cap or add fuel with the engine running. Allow engine to cool before refuelling. Do not smoke.

c)Never refuel the machine indoors.

d)Never store the machine or fuel container inside where there is an open flame, such as in a water heater.

2.Never run a machine inside a closed area.

3.Keep nuts and bolts, especially blade attach- ment bolts, tight and keep equipment in good condition.

4.Never tamper with safety devices. Check their proper operation regularly.

5.Keep machine free of grass, leaves or other debris build-up. Clean up oil or fuel spillage. Allow machine to cool before storing.

6.Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

7.Never make adjustments or repairs with the engine running.

8.Grass catcher components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown.

Frequently check components and replace with manufacturer’s recommended parts, when necessary.

9.Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them.

10.Check brake operation frequently. Adjust and service as required.

Travel and transport on public roads

Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use ap- proved securing devices and make sure that the machine is securely held.

Towing

If your machine has a hydrostatic transmission you should only tow it very short distances at low speed if absolutely necessary, otherwise the transmission may be damaged.

Intended use

This machine is designed solely for cutting grass on conventional lawns and other cleared and leveled ground without obstacles, as rocks, stumps etc., and, in conjunction with accessories supplied by the manufacturer even for other special tasks for which instructions are delivered with the acces- sory. Use in any other way is considered as con- trary to the intended use. Compliance with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer also constitute essential elements of the intended use.

This machine should be operated, serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognised regulations on safety and occupational medicine, and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury.

Safe operation practices for Ride-On Mowers Before starting cutting operations, train different driving operations on an open ground without people nearby until you feel familiar with handling the equipment. This is particularly important if you have no or little prior experience of driving a vehi- cle.

Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely in order to protect themselves and others from serious injury.

Never carry children, even with the blades off. They may fall off and be seriously injured or interfere with safe machine operation.

Danger, keep hands and feet away

English – 3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 101 90 Rider 14 ProSvenska Contents Safe operation practices for ride-on mowers Safety InstructionsGeneral operation II. Slope operationTravel and transport on public roads IV. ServiceTowing Intended useRead the instructions Explanation of SymbolsGeneral use Do as follows Driving on slopesChildren MaintenanceNever smoke in the vicinity of the battery or 10 1112 13 Location of the controls PresentationPresentation Speed limiter Throttle controlChoke lever Lift lever for cutting unit Cutting unitParking brake Lever for adjustment of the cutting heightSeat FuellingStarting the engine DrivingBefore starting Driving the machine Cutting tips Disengage lever Stopping the engineMaintenance schedule MaintenanceEngine hood Removing of the machine hoodsFront hood Right-hand fenderChecking of the fuel pump’s air filter Check the engine’s oil levelCheck the engine’s cooling air intake Check the transmission’s oil level Check the transmission’s air intakeChecking and adjustment of the steering wires Check the level of the battery acid Adjusting the brakesCheck the safety system Poorly adjusted brakes can result in reduced braking powerReplacing the air filter Do not use compressed air to clean the paper filterFitting the cutting unit Installing BioClip Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitRemoving the cutting unit Removing the belt Replacing the cutting unit’s belts Belt replacement on the BioClipBelt replacement on BioClip Placing in service position Service position for cutting unitMaintenance Restoring from service position Checking the blades Changing the oil Lubrication Replacement of the oil filterGeneral lubrication Lubrication of front wheel bearingsChecking the tyre pressure Checking and adjustment of the throttle wireMuffler air intake Replacement of the fuel filterCleaning the filter Problem Procedure Trouble Shooting ScheduleWinter storage ServiceStorage Wiring Diagram Rider 14 Pro Technical DataSide ejector Rear ejector BioClip«*3%5¬ Page 2000W02

14 Pro specifications

The Husqvarna 14 Pro is a reliable and powerful cutting instrument utilized primarily in professional applications. Designed with the heavy-duty user in mind, this saw exemplifies efficiency and durability, making it an essential tool for construction and woodworking professionals.

One of the main features of the Husqvarna 14 Pro is its robust engine, which boasted a high power-to-weight ratio. With its advanced two-stroke engine technology, it provides excellent performance while maintaining lower fuel consumption and emissions. The efficient engine is designed for optimal power delivery, ensuring that the user can tackle the toughest cutting tasks with confidence.

The 14 Pro features a 14-inch cutting blade, allowing users to make precise cuts through a variety of materials, including concrete, asphalt, and masonry. The blade's design contributes to both improved performance and longevity, making it a cost-effective choice for professionals who rely on dependable tools to complete their projects on time.

One of the standout technologies integrated into the Husqvarna 14 Pro is the Active Air Filtration system. This innovative feature ensures that the engine is well-protected from contaminants, extending the lifespan of the saw and maintaining peak performance. Alongside this system is the Wet Cutting Kit option, which allows for wet cutting applications to minimize dust and improve cut quality.

Ergonomics play a significant role in the design of the Husqvarna 14 Pro. The saw comes equipped with adjustable handles, ensuring that professionals can work comfortably for extended periods. The lightweight design also contributes to reduced user fatigue, allowing for more efficient operation throughout the day.

Safety is another vital aspect of the Husqvarna 14 Pro. The saw is equipped with several safety features, including a protective guard and an emergency stop button. These features provide peace of mind to users, assuring them that they can operate the tool with minimized risk.

In summary, the Husqvarna 14 Pro stands out in the category of cutting saws due to its powerful engine, advanced filtration technology, precision cutting capabilities, ergonomic design, and robust safety features. Ideal for professionals in construction and masonry, the Husqvarna 14 Pro is designed not just to meet but to exceed the expectations of demanding users, marking it as a trusted ally in heavy-duty applications.
Top Page Image Contents