Husqvarna 334T Tensioning the chain, Sharpening cutting teeth, Adjustment of depth gauge setting

Page 12

GENERAL SAFETY PRECAUTIONS

Sharpening cutting teeth

To sharpen cutting teeth you will need a round file and a file gauge. See instructions under the heading Technical data for information on the size of file and gauge that are recommended for the chain fitted to your chain saw.

•Check that the chain is correctly tensioned. A slack chain will move sideways, making it more difficult to sharpen correctly.

•Always file cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one side first, then turn the chain saw and file the teeth on the other side.

•File all the teeth to the same length. When the length of the cutting teeth is reduced to 4 mm (0.16") the chain is worn out and should be replaced.

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting.

See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

WARNING! The risk of kickback is increased

!if the depth gauge setting is too large!

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off the

!bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Loosen the bar nut that holds the clutch cover and chain brake. Use the combination spanner.

12 – English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 334T 338XPT KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Stop switch Throttle lockChain catcher Vibration damping systemCutting equipment MufflerGeneral rules Cutting equipment designed to reduce kickbackSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingTensioning the chain Sharpening cutting teethLubricating cutting equipment Chain oilFilling with chain oil Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentAssembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsDo not let go of the handles Basic cutting technique GeneralTerms Felling technique for tree tops CuttingLimbing Safe distanceFelling Directional cutsGeneral advice Freeing a tree that has fallen badlyCutting trees and branches that are in tension How to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking brake band wear Checking the front hand guardChecking the brake trigger Muffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAdjustment of the oil pump Air filterSpark plug Lubricating the bar tip sprocketCooling system Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations, model 334T Bar and chain combinations, model 338XPTSaw chain filing and file gauges Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions´z+R*G¶55¨ Page 1150103-95 ´z+R*G¶55¨ ´z+R*G¶55¨
Related manuals
Manual 57 pages 161 b
Top Page Image Contents