Husqvarna 334T, 338XPT KEY to Symbols, Symbols on the machine, Symbols in the operator’s manual

Page 2

KEY TO SYMBOLS

Symbols on the machine:

WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others.

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

• Approved protective helmet

• Approved hearing protection

• Protective goggles or a visor

Both of the operator′s hands must be used to operate the chain saw.

Never operate a chain saw holding it with one hand only.

Never let the guide bar tip come in contact with any object.

WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury.

Other symbols/decals on the machine refer to special certiﬁcation requirements for certain markets.

Symbols in the operator’s manual:

Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance.

Working position

Choke

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

Refuelling.

Filing with oil and adjusting oil ﬂow.

The chain brake must be engaged when the chain saw is started.

WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury.

You will ﬁnd the following labels on your chain saw:

EPA II

The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours.

Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual.

2 – English

Image 2

Contents 334T 338XPT Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Chain catcher Stop switchThrottle lock Vibration damping systemGeneral rules Cutting equipmentMufﬂer Cutting equipment designed to reduce kickbackSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain General advice on adjusting depth gauge settingAdjustment of depth gauge setting Sharpening cutting teethFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentAssembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsDo not let go of the handles Terms Basic cutting techniqueGeneral Limbing Felling technique for tree topsCutting Safe distanceFelling Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Cutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the brake trigger Checking brake band wearChecking the front hand guard Mufﬂer Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springSpark plug Adjustment of the oil pumpAir ﬁlter Lubricating the bar tip sprocketCooling system Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain ﬁling and ﬁle gauges Bar and chain combinations, model 334TBar and chain combinations, model 338XPT Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions´z+R*G¶55¨ Page 1150103-95 ´z+R*G¶55¨ ´z+R*G¶55¨

Related manuals

Manual 57 pages 161 b