Husqvarna Bar and chain combinations, model 334T, Bar and chain combinations, model 338XPT

Page 35

TECHNICAL DATA

Recommended original and replacement bar and chain combinations

Following is a list of recommended cutting equipment for the Husqvarna chain saw models 334T and 338XPT. The combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and vibration requirements of ANSI B 175.1–2000.

The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a hard nose.

The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback reduction.

As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.

Low kickback saw chain is a chain which has only met the kickback performance requirements of ANSI B 175.1 safety requirements for gasoline powered chain saws when tested on the representative sample of chain saws below 3.8 cu. in. specified in ANSI 175.1. We recommend that you as a replacement use the listed chains or "Low kickback saw chains" which are available at your dealer.

Bar and chain combinations, model 334T

Bar

 

 

 

Chain

 

 

 

 

 

 

 

Length, inch

Pitch, inch

Gauge, mm

Max. nose radius

Type

Drive link count

 

 

 

 

 

 

12

3/8

1,3

7 T

Husqvarna H36

45

 

 

 

 

 

14

3/8

1,3

7 T

52

 

 

 

 

 

 

 

Bar and chain combinations, model 338XPT

 

 

Bar

 

 

 

Chain

 

 

 

 

 

 

 

Length, inch

Pitch, inch

Gauge, mm

Max. nose radius

Type

Drive link count

 

 

 

 

 

 

12

3/8

1,3

9 T

 

45

 

 

 

 

 

 

14

3/8

1,3

9 T

Husqvarna H36

52

 

 

 

 

 

 

16

3/8

1,3

9 T

 

56

 

 

 

 

 

 

Saw chain filing and file gauges

English – 35

Image 35
Contents 334T 338XPT Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Stop switchThrottle lock Chain catcherCutting equipment designed to reduce kickback Cutting equipmentMuffler General rulesGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainChecking chain lubrication Lubricating cutting equipmentChain oil Filling with chain oilChecking wear on cutting equipment Chain drive sprocketFitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useDo not let go of the handles Terms Basic cutting techniqueGeneral Safe distance Felling technique for tree topsCutting LimbingDirectional cuts FellingCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Cutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the brake trigger Checking brake band wearChecking the front hand guard Muffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springLubricating the bar tip sprocket Adjustment of the oil pumpAir filter Spark plugCooling system Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinations, model 334TBar and chain combinations, model 338XPT Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions´z+R*G¶55¨ Page 1150103-95 ´z+R*G¶55¨ ´z+R*G¶55¨
Related manuals
Manual 57 pages 161 b