Husqvarna 338XPT, 334T manual Muffler, Chain catcher

Page 29

MAINTENANCE

Chain catcher

Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw.

Vibration damping system

Regularly check the vibration damping units for cracks or deformation.

Make sure the vibration damping units are securely attached to the engine unit and handle unit.

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. This is best done with a wire brush. A blocked mesh will cause the engine to overheat and may lead to serious damage.

Note! The mesh must be replaced if it is damaged. If the mesh is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition.

Never use a muffler if the spark arrestor mesh is missing or defective.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

A muffler equipped with a catalytic converter significantly reduces the amount of hydrocarbons (HC), nitrogen oxides (NO) and aldehydes in the exhaust fumes. Carbon monoxide (CO), which is poisonous and odorless, is not however reduced! Consequently, never work in an enclosed or badly ventilated area. Good air circulation should always prevail when working in snowy hollows, ravines or in confined conditions.

English – 29

Image 29
Contents 334T 338XPT Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Throttle lock Stop switchChain catcher Vibration damping systemMuffler Cutting equipmentGeneral rules Cutting equipment designed to reduce kickbackGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingAdjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Sharpening cutting teethChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketFitting the bar and chain AssemblyFuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsDo not let go of the handles Terms Basic cutting techniqueGeneral Cutting Felling technique for tree topsLimbing Safe distanceDirectional cuts FellingCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Cutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the brake trigger Checking brake band wearChecking the front hand guard Muffler Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springAir filter Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketCooling system Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinations, model 334TBar and chain combinations, model 338XPT Your Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions´z+R*G¶55¨ Page 1150103-95 ´z+R*G¶55¨ ´z+R*G¶55¨
Related manuals
Manual 57 pages 161 b