Husqvarna 353 EPA I Before using a new chain saw, Please read the operator’s manual carefully

Page 4

CONTENTS

Before using a new chain saw

•Please read the operator’s manual carefully.

•Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly.

•Refuel, start the chain saw and check the carburettor settings. See the instructions under the headings Fuel Handling, Starting and Stopping, and Carburettor.

•Do not use the chain saw until sufficient chain oil has reached the chain. See instructions under the heading Lubricating cutting equipment.

IMPORTANT! If the carburettor mixture is too lean it greatly increases the risk of engine failure. Poor maintenance of the air filter will cause carbon build-up on the spark plug and lead to starting difficulties. If the chain is improperly adjusted it will cause increased wear or damage to the bar, drive sprocket and chain.

Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual.

WARNING! Under no circumstances may the

!design of the machine be modified without the permission of the manufacturer. Always use genuine accessories. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others. Your warranty may not cover damage or liability caused by the use of non-authorized accessories or replacement parts.

WARNING! A chain saw is a dangerous tool

!if used carelessly or incorrectly and can cause serious, even fatal injuries. It is very important that you read and understand the contents of this operator’s manual.

WARNING! The inside of muffler contain

!chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muffler.

WARNING! Long term inhalation of the

!engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a health risk.

You will find the following labels on your machine:

EPA I

EPA II

The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice.

For customer assistance call: 704-921-7000 or contact us at

our website: www.husqvarna.com

4 – English

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Operator’s manual EPA KEY to Symbols Key to symbolsContents Before using a new chain saw Please read the operator’s manual carefullyMachine′s safety equipment Safety InstructionsPersonal protective equipment Chain brake and front hand guard Stop switch Throttle lockChain catcher Right hand guardMuffler Checking brake band wearChecking the front hand guard Checking the inertia brake releaseStop switch Throttle lockChain catcher Right hand guardCutting equipment General rulesCutting equipment designed to minimise kickback BarSome terms that describe the bar and chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Setting the raker clearance General advice on setting raker clearanceSharpening cutting teeth Tensioning the chain Lubricating cutting equipmentChain oil Filling with chain oilChecking chain lubrication Lubricating the bar tip sprocketNeedle bearing lubrication Checking wear on cutting equipmentHow to avoid kickback What is kickback?General safety precautions Starting Fuel safetyTransport and storage Basic safety rules General working instructionsBasic cutting technique GeneralCutting Tree felling technique LimbingSafe distance Felling directionFelling Directional cutsGeneral advice Freeing a tree that has fallen badlyCutting the trunk into logs Freeing a trapped treeWhat is WHAT? What is what on the chain saw?Assembly Fitting the bar and chainFuel Fuel HandlingFollowing applies to chain saws with catalytic converters Chain oil FuellingFuel Handling Starting and Stopping Starting and stoppingCold engine Warm engineStopping Maintenance CarburettorCorrectly adjusted carburettor StarterChanging a broken or worn starter cord Tensioning the recoil springAir filter Spark plugMuffler Fitting the starterAdjustment of the oil pump Air Injection centrifugal cleaningNeedle bearing lubrication Cooling systemTemperature 0 C 32 F or colder Temperature -5C 23 F or colderHeated handles Electrical carburettor heatingDaily maintenance Weekly maintenanceMonthly maintenance Below you will find some general maintenance instructionsTechnical Data Technical dataBar Chain Length, inches Pitch, inch Max nose radius Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Control Warranty Parts List 1140204-95
Top Page Image Contents