Husqvarna 346XP EPA II, 353 EPA I manual Needle bearing lubrication, Adjustment of the oil pump

Page 33

MAINTENANCE

Consequently, never work in an enclosed or badly ventilated area. Good air circulation should always prevail when working in snowy hollows, ravines or in confined conditions.

WARNING! The catalytic converter muffler

!gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when working near flammable substances and/or vapours.

Needle bearing lubrication

The clutch drum is fitted with one of the following drive sprockets:

A Spur sprocket (the chain sprocket is welded on the drum)

B Rim sprocket (replaceable)

Both versions have a needle bearing on the drive shaft, which has to be greased regularly (once a week).

CAUTION! Use only high quality bearing grease or engine oil.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

 

+

2

1

 

3

WARNING! The engine must not be running

!when making adjustments.

Recommended settings:

Bar 13"-15": Position 1

Bar 15"-18": Position 2

Bar 18"-20": Position 3

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Air guide plate.

3Fins on the flywheel.

4Cooling fins on the cylinder.

5Cylinder cover (directs cold air over the cylinder).

5

4

3

2

1

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

”Air Injection” centrifugal cleaning

Centrifugal cleaning means the following: All air to the carburettor passes through the starter. Dirt and dust is centrifuged out by the cooling fan.

IMPORTANT! In order to maintain operation of the centrifugal cleaning system it must be regularly maintained.

Clean the air intake to the starter, the fins on the flywheel, the space around the flywheel, inlet pipe and carburettor compartment.

English – 33

Image 33
Contents Operator’s manual EPA Key to symbols KEY to SymbolsContents Please read the operator’s manual carefully Before using a new chain sawSafety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardChecking brake band wear MufflerChecking the front hand guard Checking the inertia brake releaseThrottle lock Stop switchChain catcher Right hand guardGeneral rules Cutting equipmentCutting equipment designed to minimise kickback BarSharpening your chain and adjusting raker clearance Some terms that describe the bar and chainGeneral information on sharpening cutting teeth General advice on setting raker clearance Setting the raker clearanceSharpening cutting teeth Lubricating cutting equipment Tensioning the chainChain oil Filling with chain oilLubricating the bar tip sprocket Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentWhat is kickback? How to avoid kickbackGeneral safety precautions Fuel safety StartingTransport and storage General working instructions Basic safety rulesBasic cutting technique GeneralCutting Limbing Tree felling techniqueSafe distance Felling directionDirectional cuts FellingFreeing a tree that has fallen badly General adviceCutting the trunk into logs Freeing a trapped treeWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFuel Handling FuelFollowing applies to chain saws with catalytic converters Fuelling Chain oilFuel Handling Starting and stopping Starting and StoppingCold engine Warm engineStopping Carburettor MaintenanceStarter Correctly adjusted carburettorChanging a broken or worn starter cord Tensioning the recoil springSpark plug Air filterMuffler Fitting the starterAir Injection centrifugal cleaning Adjustment of the oil pumpNeedle bearing lubrication Cooling systemTemperature -5C 23 F or colder Temperature 0 C 32 F or colderHeated handles Electrical carburettor heatingWeekly maintenance Daily maintenanceMonthly maintenance Below you will find some general maintenance instructionsTechnical data Technical DataBar Chain Length, inches Pitch, inch Max nose radius Your Warranty Rights and Obligations Federal Emission Control Warranty StatementEmission Control Warranty Parts List 1140204-95