Husqvarna 345e Felling direction, Clearing the trunk and preparing your retreat, Directional cuts

Page 25

WORKING TECHNIQUES

Felling direction

The aim is to fell the tree in a position where you can limb and cross-cut the log as easily as possible. You want it to fall in a location where you can stand and move about safely.

Once you have decided which way you want the tree to fall you must judge which way the tree would fall naturally.

Several factors affect this:

•Lean of the tree

•Bend

•Wind direction

•Arrangement of branches

•Weight of snow

•Obstacles within the reach of the tree: for example, other trees, power lines, roads and buildings.

•Look for signs of damage and rot in the stem, this makes it more probably that the tree will break and start to fall before you expect it to.

You may find you are forced to let the tree fall in its natural direction because it is impossible or dangerous to try to make it fall in the direction you first intended.

Another very important factor, which does not affect the felling direction but does affect your safety, is to make sure the tree has no damaged or dead branches that might break off and hit you during felling.

The main point to avoid is letting the tree fall onto another tree. It is very dangerous to remove a trapped tree and there is high accident risk. See instructions under the heading Freeing a tree that has fallen badly.

IMPORTANT! During critical felling operations, hearing protectors should be lifted immediately when sawing is completed so that sounds and warning signals can be heard.

Clearing the trunk and preparing your retreat

Delimb the stem up to shoulder height. It is safer to work from the top down and to have the tree between you and the saw.

Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall.

Your path of retreat should be roughly 135 degrees away from the intended felling direction.

D

 

 

 

 

 

anger

zone

 

 

direction

 

 

Felling

 

 

 

 

 

 

 

 

 

Retreat path

 

 

 

 

 

 

 

D

 

 

Danger

zone

path

anger

zone

 

 

 

 

 

 

Retreat

 

 

 

 

 

 

 

Felling

WARNING! Unless you have special training

!we advise you not to fell trees with a diameter larger than the bar length of your saw!

Felling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then you finish with the felling cut. By placing these cuts correctly you can control the felling direction very accurately.

Directional cuts

To make the directional cuts you begin with the top cut. Stand to the right of the tree and cut on the pull stroke.

English – 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents TrioBrake Symbols on the machine KEY to SymbolsSymbols in the operator’s manual You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingAdjustment of depth gauge setting General advice on adjusting depth gauge settingIf the depth gauge setting is too large Sharpening cutting teethLubricating cutting equipment Tensioning the chainChain oil Filling with chain oilNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Bar Fitting the bar and chain AssemblyFuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms LimbingCutting Tree felling techniqueSafe distance Log is supported at one end. There is a high risk that itClearing the trunk and preparing your retreat Felling directionFelling Directional cutsFelling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking brake band wear Correctly adjusted carburetorChecking the front hand guard Checking the inertia brake releaseChecking the brake trigger Starter MufflerChanging a broken or worn starter cord 345eAir filter Replacement of broken recoil and drive disc springsTensioning the recoil spring Fitting the starterWhen making adjustments Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketCooling system Air Injection centrifugal cleaningHeated handles Electrical carburetor heatingTemperature 0C 32F or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinations058/1,5 mm 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions´z+RA¶5¨ Page 1150330-95 ´z+RA¶5¨ ´z+RA¶5¨

345e, 345, 346XP, 353 specifications

Husqvarna is renowned for crafting high-performance chainsaws, and the models 345e, 345, 346XP, and 353 are prime examples of their engineering excellence. Each of these chainsaws is designed to cater to the needs of both professionals and enthusiasts, boasting impressive features and advanced technology.

The Husqvarna 345e is a powerful yet lightweight chainsaw. It is equipped with a 50.2cc engine, delivering an impressive output of 3.0 horsepower. Its X-Torq technology reduces fuel consumption and emissions, making it an environmentally friendly option. Additionally, the chainsaw features an ergonomic design, ensuring comfort during prolonged use. The LowVib technology minimizes vibrations, reducing operator fatigue.

Next in line, the Husqvarna 345 is similar in many respects to the 345e but focuses on providing a robust and reliable performance. It also features a 50.2cc engine and utilizes X-Torq technology for optimal fuel efficiency and low emissions. One of the standout features of the 345 is its tool-less chain tensioning system, allowing for easy adjustments without the need for additional tools. This is particularly advantageous for users who require quick adjustments in the field.

The Husqvarna 346XP is a favorite among professionals, designed for heavy-duty tasks. Its X-Torq engine delivers exceptional power, while its lightweight construction enhances maneuverability. The 346XP features Air Injection technology, which reduces the amount of dust and debris that enters the air filter, prolonging the life of the chainsaw. Additionally, the chainsaw’s adjustable oil pump ensures that the chain receives the right amount of lubrication, optimizing performance and longevity.

The Husqvarna 353 is built for versatility and performance. With a 50cc engine, it provides ample power for a wide range of cutting tasks. Its innovative features include a robust crankshaft designed for higher revolutions, enhancing overall performance. The 353 also incorporates the innovative Smart Start technology, making it easier to start the engine with minimal effort. Its ergonomic design ensures comfortable operation, reducing fatigue during extended use.

In summary, the Husqvarna 345e, 345, 346XP, and 353 chainsaws are distinguished by their advanced technologies and user-friendly features. Whether for professional use or as a reliable tool for everyday tasks, these models exemplify Husqvarna’s commitment to quality, efficiency, and performance.
Top Page Image Contents