Husqvarna 345, 346XP, 353 manual Muffler, Starter, Changing a broken or worn starter cord, 345e

Page 32

MAINTENANCE

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week. This is best done with a wire brush. A blocked screen will cause the engine to overheat and may lead to serious damage.

Note! The screen must be replaced if it is damaged. If the screen is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor screen is missing or defective.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator.The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

A muffler equipped with a catalytic converter significantly reduces the amount of hydrocarbons (HC), nitrogen oxides (NO) and aldehydes in the exhaust fumes. Carbon monoxide (CO), which is poisonous and odorless, is not however reduced! Consequently, never work in an enclosed or badly ventilated area. Good air circulation should always prevail when working in snowy hollows, ravines or in confined conditions.

Starter

WARNING! When the recoil spring is wound

!up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring, starter cord or the drive disc spring. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

345e:

•Undo the bolt in the centre of the pulley and remove the drive disc, drive disc spring and the pulley. Insert and secure a new starter cord in the starter pulley. Wind approx. 3 turns of the starter cord on the starter pulley. Fit the starter pulley so that the end of the recoil spring hooks into the starter pulley. Now assemble the drive disc spring, drive disc and the bolt in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Tie a good knot on the starter cord.

32 – English

Page 31 Page 33
Image 32
Page 31 Page 33
Contents TrioBrake KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingIf the depth gauge setting is too large Sharpening cutting teethTensioning the chain Lubricating cutting equipmentChain oil Filling with chain oilChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Bar Assembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique GeneralTerms LimbingTree felling technique CuttingSafe distance Log is supported at one end. There is a high risk that itFelling direction Clearing the trunk and preparing your retreatFelling Directional cutsFelling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment Correctly adjusted carburetor Checking brake band wearChecking the front hand guard Checking the inertia brake releaseChecking the brake trigger Muffler StarterChanging a broken or worn starter cord 345eReplacement of broken recoil and drive disc springs Air filterTensioning the recoil spring Fitting the starterAdjustment of the oil pump When making adjustmentsSpark plug Lubricating the bar tip sprocketAir Injection centrifugal cleaning Cooling systemHeated handles Electrical carburetor heatingTemperature 0C 32F or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gauges058/1,5 mm 050/1,3 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions´z+RA¶5¨ Page 1150330-95 ´z+RA¶5¨ ´z+RA¶5¨

345e, 345, 346XP, 353 specifications

Husqvarna is renowned for crafting high-performance chainsaws, and the models 345e, 345, 346XP, and 353 are prime examples of their engineering excellence. Each of these chainsaws is designed to cater to the needs of both professionals and enthusiasts, boasting impressive features and advanced technology.

The Husqvarna 345e is a powerful yet lightweight chainsaw. It is equipped with a 50.2cc engine, delivering an impressive output of 3.0 horsepower. Its X-Torq technology reduces fuel consumption and emissions, making it an environmentally friendly option. Additionally, the chainsaw features an ergonomic design, ensuring comfort during prolonged use. The LowVib technology minimizes vibrations, reducing operator fatigue.

Next in line, the Husqvarna 345 is similar in many respects to the 345e but focuses on providing a robust and reliable performance. It also features a 50.2cc engine and utilizes X-Torq technology for optimal fuel efficiency and low emissions. One of the standout features of the 345 is its tool-less chain tensioning system, allowing for easy adjustments without the need for additional tools. This is particularly advantageous for users who require quick adjustments in the field.

The Husqvarna 346XP is a favorite among professionals, designed for heavy-duty tasks. Its X-Torq engine delivers exceptional power, while its lightweight construction enhances maneuverability. The 346XP features Air Injection technology, which reduces the amount of dust and debris that enters the air filter, prolonging the life of the chainsaw. Additionally, the chainsaw’s adjustable oil pump ensures that the chain receives the right amount of lubrication, optimizing performance and longevity.

The Husqvarna 353 is built for versatility and performance. With a 50cc engine, it provides ample power for a wide range of cutting tasks. Its innovative features include a robust crankshaft designed for higher revolutions, enhancing overall performance. The 353 also incorporates the innovative Smart Start technology, making it easier to start the engine with minimal effort. Its ergonomic design ensures comfortable operation, reducing fatigue during extended use.

In summary, the Husqvarna 345e, 345, 346XP, and 353 chainsaws are distinguished by their advanced technologies and user-friendly features. Whether for professional use or as a reliable tool for everyday tasks, these models exemplify Husqvarna’s commitment to quality, efficiency, and performance.
Top Page Image Contents