Husqvarna 345, 346XP, 353, 345e manual Felling cut

Page 26

WORKING TECHNIQUES

Next make the bottom cut so that it finishes exactly at the end of the top cut.

The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°.

The line where the two cuts meet is called the directional cut line. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

Felling cut

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut on the pull stroke.

Make the felling cut about 1.5-2 inches (3-5 cm) above the bottom directional cut.

Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter. The uncut section of the trunk is called the felling hinge.

The felling hinge controls the direction that the tree falls in.

All control over the felling direction is lost if the felling hinge is too narrow or non-existent, or if the directional cuts and felling cut are badly placed.

When the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a felling wedge or breaking bar.

We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommended for your saw.

There are methods for felling trees with a diameter larger than the bar length. However these methods involve a much greater risk that the kickback zone of the bar will come into contact with the tree.

26 – English

Page 25 Page 27
Image 26
Page 25 Page 27
Contents TrioBrake Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Sharpening cutting teethChain oil Tensioning the chainLubricating cutting equipment Filling with chain oilChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Bar Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral LimbingSafe distance Tree felling techniqueCutting Log is supported at one end. There is a high risk that itFelling Felling directionClearing the trunk and preparing your retreat Directional cutsFelling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment Checking the front hand guard Correctly adjusted carburetorChecking brake band wear Checking the inertia brake releaseChecking the brake trigger Changing a broken or worn starter cord MufflerStarter 345eTensioning the recoil spring Replacement of broken recoil and drive disc springsAir filter Fitting the starterSpark plug Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningCooling system Electrical carburetor heatingTemperature 0C 32F or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions´z+RA¶5¨ Page 1150330-95 ´z+RA¶5¨ ´z+RA¶5¨

345e, 345, 346XP, 353 specifications

Husqvarna is renowned for crafting high-performance chainsaws, and the models 345e, 345, 346XP, and 353 are prime examples of their engineering excellence. Each of these chainsaws is designed to cater to the needs of both professionals and enthusiasts, boasting impressive features and advanced technology.

The Husqvarna 345e is a powerful yet lightweight chainsaw. It is equipped with a 50.2cc engine, delivering an impressive output of 3.0 horsepower. Its X-Torq technology reduces fuel consumption and emissions, making it an environmentally friendly option. Additionally, the chainsaw features an ergonomic design, ensuring comfort during prolonged use. The LowVib technology minimizes vibrations, reducing operator fatigue.

Next in line, the Husqvarna 345 is similar in many respects to the 345e but focuses on providing a robust and reliable performance. It also features a 50.2cc engine and utilizes X-Torq technology for optimal fuel efficiency and low emissions. One of the standout features of the 345 is its tool-less chain tensioning system, allowing for easy adjustments without the need for additional tools. This is particularly advantageous for users who require quick adjustments in the field.

The Husqvarna 346XP is a favorite among professionals, designed for heavy-duty tasks. Its X-Torq engine delivers exceptional power, while its lightweight construction enhances maneuverability. The 346XP features Air Injection technology, which reduces the amount of dust and debris that enters the air filter, prolonging the life of the chainsaw. Additionally, the chainsaw’s adjustable oil pump ensures that the chain receives the right amount of lubrication, optimizing performance and longevity.

The Husqvarna 353 is built for versatility and performance. With a 50cc engine, it provides ample power for a wide range of cutting tasks. Its innovative features include a robust crankshaft designed for higher revolutions, enhancing overall performance. The 353 also incorporates the innovative Smart Start technology, making it easier to start the engine with minimal effort. Its ergonomic design ensures comfortable operation, reducing fatigue during extended use.

In summary, the Husqvarna 345e, 345, 346XP, and 353 chainsaws are distinguished by their advanced technologies and user-friendly features. Whether for professional use or as a reliable tool for everyday tasks, these models exemplify Husqvarna’s commitment to quality, efficiency, and performance.
Top Page Image Contents