Husqvarna 45 manual Air filter, Muffler, Needle bearing maintenance, Spark plug

Page 31

MAINTENANCE

Air filter

The air filter must be regularly cleaned from dust and dirt in order to avoid:

•Carburetor malfunctions

•Starting problems

•Engine power reduction

•Unnecessary wear on

the engine parts

• Abnormal fuel consumption

Clean the air filter daily or more often if the air is exceptionally dusty in the working area.

• Disassemble the air filter by removing the cylinder cover and unscrew the filter.

When reassembling, make sure that the filter is tight against the filter holder. Clean the filter by brushing or shaking it.

•A more thorough cleaning of the filter is obtained by washing it in water and soap.

An air filter, which is used for some time, cannot be cleaned completely. Therefore it must be replaced by a new one,

Muffler

The muffler is designed in order to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material. Some mufflers are equipped with a special screen. If your saw has this type of muffler, you should clean the screen at least once a week. This is done with a wire brush.

CAUTION! The screen must be replaced, if damaged. The saw will be overheated, if the screen is clogged. This results in damage on the cylinder and the piston. Never use a saw with a clogged or defective muffler.

Needle bearing maintenance

with regular intervals.

IMPORTANT! A damaged air filter must always be replaced.

Spark plug

The spark plug condition is influenced by:

•An incorrect carburetor setting.

•Wrong fuel mixture (too much oil in the gasoline).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in malfunction and starting difficulties.

If the engine is low on

 

power, difficult to start or

0,5 mm

runs poorly at idling speed,

 

always check the spark plug

 

first. If the spark plug is dirty,

 

clean it and check the

 

electrode gap. Readjust if

 

necessary. The correct gap is

 

0,5 mm (0,020"). The spark

 

plug should be replaced after

 

about a month in operation or

 

earlier if the electrodes are

 

badly eroded.

 

IMPORTANT! Always use the recommended spark plug type. An incorrect spark plug can severely damage the piston/cylinder.

The clutch drum is equipped with one of the following chain sprockets:

•Spur sprocket (A) (the chain sprocket is welded on the drum)

•Rim sprocket (B) (exchangeable)

Both versions have built-in needle bearing at the drive shaft, whitch has to be greased regularly (once a week).

NOTE! Use only high quality bearing grease.

A

B

English – 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 101 90 45/49Symbols KEY to SymbolsContents Chain SAW Safety Equipment Safety InstructionsPersonal Protective Equipment Chain brake and front hand guard Chain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the automatic brakeThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Setting the raker clearance General advice on setting raker clearanceTensioning the chain Chain oil Lubricating cutting equipmentFilling with chain oil Lubricating the bar tip sprocket Checking chain lubricationLubricating the clutch drum bearing Checking wear on cutting equipmentWhat is kickback? HOW to Avoid KickbackDo not let go of the handles General rulesMin m General Safety Precautions10 ft General Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatCutting trees and branches that are in tension Preparations Freeing a tree that has fallen badly = high accident riskCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? Mounting guide bar and chain AssemblyFuelmix Fuel HandlingMin 3 m Fuelling10ft Start Start and StopCold engine Warm engineCarburetor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordSpark plug Needle bearing maintenanceAir filter MufflerCentrifugal cleaning Air Injection Daily maintenanceCooling system Weekly maintenance Monthly maintenance Technical Data Your Warranty Rights Obligations Federal Emission Control Warranty Statement1998W48

45 specifications

The Husqvarna 45 is a powerful and reliable chainsaw designed for both novice and experienced users looking for a versatile tool for various cutting tasks. Known for its durability and performance, this chainsaw is suitable for everything from felling trees to cutting firewood, making it a favorite among homeowners, gardeners, and landowners.

One of the main features of the Husqvarna 45 is its lightweight design, weighing in at around 11 lbs. This makes it easy to handle and maneuver, allowing users to work for extended periods without experiencing undue fatigue. Its ergonomic design includes a comfortable handle that provides a secure grip and helps maintain control during operation.

The chainsaw is powered by a robust 45cc X-Torq engine, which delivers a strong performance while minimizing fuel consumption and exhaust emissions. This innovative engine technology not only enhances power output but also decreases the environmental impact, aligning with today’s demand for eco-friendly tools. With a power output of 2.4 kW, the Husqvarna 45 can handle tough cutting tasks with ease.

To ensure optimal cutting efficiency, the Husqvarna 45 features an automatic oil pump that adjusts oil flow based on chain speed and temperature, providing the right amount of lubrication for enhanced performance and durability. Additionally, the chain tensioning system allows for quick and easy adjustments without the need for additional tools, ensuring that users can maintain the chainsaw with minimal effort.

Safety is another critical aspect of the Husqvarna 45. It incorporates several safety features, including a chain brake that engages automatically when the front handle is activated. This prevents kickback and improves user safety, making it suitable for operators of varying skill levels. The chainsaw also includes a hand guard to further protect users from potential accidents.

In summary, the Husqvarna 45 is a well-rounded chainsaw featuring a lightweight, ergonomic design, a powerful X-Torq engine, and automatic oiling for optimal performance. With its focus on safety and user-friendliness, this chainsaw is an excellent choice for anyone looking to tackle various cutting tasks around the home or property. Whether you are clearing brush, cutting firewood, or performing tree maintenance, the Husqvarna 45 is equipped to deliver reliable results with every use.
Top Page Image Contents