Setup and Adjustments, Cutting Height | Husqvarna WHF5219, WHF5217

SETUP AND ADJUSTMENTS

1.Uncrate mower

2.Lift up on handles until mower is level.

3.Using the hardware provided in the literature package, insert 3 bolts per side into the frame side where the front frame connects to the rear deck. (See FIG 1) A pry bar can be used to align the holes.

CUTTING HEIGHT:

1.Stop the mower and disengage the blades.

2.Raise the deck height lever to the transport po- sition.

3.Remove the height adjustment pin and place it in the desired cutting height hole. Move deck height lever down onto the pin and mow. NOTE: anti-scalp rollers must be in the proper position for maximum deck floatation. See the decal on the front deck.

FIGURE 1

4.Line up the back edge of the front frame with the front edge of the wheel motor mount so they are parallel and tighten the hardware.

5.Remove the hood from the frame and install the deck belt. Be sure the belt is still wrapped around the clutch pulley under the rear deck.(See FIG 2)

6.With the hood off, mount the muffler on the engine using the provided hardware. Reinstall hood.

7.Cut the plastic wire ties holding the operator presence levers down.

8.Check tire pressure in all four tires. (rear tires 15 PSI, front tires 20-25 PSI)

9.Check engine oil with dipstick. Add if needed per engine manufactures specifications. (See engine manual)

10.Check hydraulic oil level. Should be an 1.0” below the bottom of the fill tube.

11.Mount the discharge chute to the front deck using the fasteners provided on the deck.

MOWER DECK LEVELING:

1.Position mower on a flat surface and stop en- gine.

2.Check the tire pressure of all four tires. Infla- tion should be 15 psi.

3.Place two 2x4’s on edge under the cutting deck from front to rear and lower the deck down onto the 2x4’s.

4.Adjust the four upper chain bolts “H” to the cen- ter of the slot in the deck lift arms. NOTE: make sure deck lift blocks are tightly bolted to the frame .

5.Check chains for equal tension. If unequal, adjust upper chain bolt in slot.

6.Place deck in the 5" cutting height and mea- sure from the cutting edge of the blade to a flat surface to check deck cutting height.

WHF5219, WHF5217, WHF4817 specifications

The Husqvarna WHF4817, WHF5219, and WHF5217 are part of Husqvarna’s renowned line of walk-behind lawn mowers, designed for both residential and professional use. These models are tailored for effective grass cutting, combining efficiency, durability, and user-friendly features that cater to a range of lawn sizes and terrains.

The WHF4817 is ideal for smaller to medium-sized yards, boasting a powerful 48 cm cutting width. This mower features an adjustable cutting height, allowing users to choose between six different settings, ensuring optimum grass length for various preferences. The WHF4817 is equipped with a sturdy steel cutting deck, providing exceptional durability against wear and tear during regular use.

Moving up to the WHF5219, this model delivers a wider 52 cm cutting width, making it suitable for larger lawns while still maintaining maneuverability. It incorporates advanced technologies such as the AutoWalk self-propulsion system, which automatically adjusts the speed based on the user’s walking pace, promoting comfort and reducing operator fatigue. The WHF5219 also features a robust engine with high torque, ensuring exceptional cutting performance even in dense grass.

The WHF5217, on the other hand, integrates features that cater to versatility. With a 52 cm cutting width like the WHF5219, it allows for efficient mowing over larger areas. Its ergonomic design, complete with an adjustable handle, facilitates easy navigation even in tight spaces. The WHF5217’s blade braking system enhances safety by stopping the blade quickly when the operator releases the handle, minimizing the risk of accidents during operation.

Each model utilizes Husqvarna's signature Easy Start technology, which ensures that starting the engine is effortless, even in cold conditions. Additionally, all three models support mulching capabilities, allowing users to recycle grass clippings back into the lawn, promoting healthy growth and reducing waste.

With service-friendly features such as easy access to the engine for maintenance and a folding handle for compact storage, the WHF4817, WHF5219, and WHF5217 are designed for convenience and longevity. These walk-behind mowers combine efficiency with advanced technology, making them an ideal choice for homeowners and professionals alike seeking high-quality lawn care solutions.