Husqvarna 445 EPA II, 445e EPA II, 450e EPA II Chain drive sprocket, Needle bearing lubrication

Page 15

GENERAL SAFETY PRECAUTIONS

•Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary.

If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your servicing dealer.

Chain drive sprocket

The clutch drum is fitted with one of the following drive sprockets:

ASpur sprocket (the chain sprocket is welded on the drum)

BRim sprocket (replaceable)

Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain.

Needle bearing lubrication

Both versions of sprockets have a needle bearing on the drive shaft, which has to be greased regularly (once a week). CAUTION! Use only high quality bearing grease or engine oil.

See instructions under the heading Maintenance, Needle bearing lubrication.

Checking wear on cutting equipment

Check the chain daily for:

•Visible cracks in rivets and links.

•Whether the chain is stiff.

•Whether rivets and links are badly worn.

Replace the saw chain if it exhibits any of the points above.

We recommend you compare the existing chain with a new chain to decide how badly the existing chain is worn.

When the length of the cutting teeth has worn down to only 0.16 inch (4 mm) the chain must be replaced.

Bar

Check regularly:

•Whether there are burrs on the edges of the bar. Remove these with a file if necessary.

•Whether the groove in the bar has become badly worn. Replace the bar if necessary.

•Whether the tip of the bar is uneven or badly worn. If a hollow forms on the underside of the bar tip this is due to running with a slack chain.

•To prolong the life of the bar you should turn it over regularly.

WARNING! Most chain saw accidents

!happen when the chain touches the operator.

Wear personal protective equipment. See instructions under the heading Personal protective equipment.

Do not tackle any job that you feel you are not adequately trained for. See instructions under the headings Personal protective equipment, How to avoid kickback, Cutting equipment and General working instructions.

Avoid situations where there is a risk of kickback. See instructions under the heading Machine′s safety equipment.

Use the recommended protective equipment and check its condition. See instructions under the heading General working instructions.

Check that all the chain saw safety features are working. See instructions under the headings General working instructions and General safety precautions.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents English EPA II 445e EPA 450e EPAKEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth General advice on adjusting depth gauge setting445e, 450e Adjustment of depth gauge settingTensioning the chain 445Checking chain lubrication Lubricating cutting equipmentChain oil Filling with chain oilChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment 445e, 450e AssemblyFitting the bar and chain 445Assembly Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Limbing Basic cutting techniqueGeneral TermsClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionDirectional cuts FellingHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking the brake trigger Checking the inertia brake releaseMuffler Replacing the return and drive springs StarterReplacing the starter cord Tensioning the recoil springNeedle bearing lubrication Air filterSpark plug Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Cooling systemDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions1150341-95 ´z+RB3¶55¨ ´z+RB3¶55¨

445 EPA II, 445e EPA II, 450e EPA II specifications

Husqvarna is a name synonymous with power and durability, especially when it comes to its line of chainsaws like the Husqvarna 445 EPA II, 445e EPA II, and 450e EPA II. These models combine advanced technology and ergonomic design to fulfill the needs of both professional users and homeowners.

The Husqvarna 445 EPA II chainsaw is designed for versatility and ease of use. It boasts a 45.7cc engine, providing a balance of power and weight ideal for various cutting tasks. The chainsaw features Husqvarna’s X-Torq engine technology, which reduces emissions and improves fuel efficiency. This means less downtime for refueling and a smaller ecological footprint, making it environmentally friendly. Additionally, the LowVib system minimizes vibration, which translates to reduced user fatigue over long periods of use.

The 445e EPA II takes similar principles and enhances them with increased efficiency and usability. This model includes the Air Injection system, which helps filter out larger dust and debris particles before reaching the air filter, ensuring consistent performance and a longer lifespan for the machine. Its lightweight design makes it easier to maneuver while the front handle is ergonomically shaped for a secure grip. The easy-start feature allows users to get going quickly with minimal effort.

Moving up the line, the Husqvarna 450e EPA II offers more power, featuring a slightly larger engine and an improved cutting capacity. This model is perfect for heavy-duty tasks, from felling trees to cutting firewood. Like its predecessors, it employs X-Torq engine technology and also includes the Quick Release Air Filter, making maintenance easier and faster. The robust design and advanced security features—such as the inertia-activated chain brake—ensure safe operation even under challenging conditions.

Overall, the Husqvarna 445 EPA II, 445e EPA II, and 450e EPA II chainsaws represent a commitment to safety, efficiency, and user comfort. The integration of modern technological features, coupled with Husqvarna's reputation for quality workmanship, makes these chainsaws ideal choices for anyone looking to tackle a range of outdoor cutting applications with confidence.
Top Page Image Contents