Husqvarna 445 EPA II, 445e EPA II, 450e EPA II manual Maintenance, General, Carburetor adjustment

Page 29

MAINTENANCE

General

The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop.

Carburetor adjustment

Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions.

Function

•The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. The air/ fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.

•The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic settings and running in

The basic carburetor settings are adjusted during testing at the factory. Fine adjustment should be carried out by a skilled technician.

Rec. idle speed: See the Technical data section.

Fine adjustment of the idling speed T

Adjust the idle speed with the T-screw. If it is necessary to re- adjust, turn the T-screw clockwise while the engine is running, until the chain starts to rotate. Then turn counter-clockwise until the chain stops. A correctly adjusted idle speed setting occurs when the engine runs smoothly in every position. It should also be good margin to the rpm when the chain starts to rotate.

WARNING! Contact your servicing dealer, if

!the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max. speed. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Checking, maintaining and servicing chain saw safety equipment

Note! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below we recommend you to contact our servicing dealer.

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake.

Regularly check that the brake band is at least 0.024 inch (0.6 mm) thick at its thinnest point.

Checking the front hand guard

Make sure the front hand guard is not damaged and that there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.

English – 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents English EPA II 445e EPA 450e EPASymbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth General advice on adjusting depth gauge settingTensioning the chain Adjustment of depth gauge setting445 445e, 450eChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Fitting the bar and chain Assembly445 445e, 450eAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFreeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment Checking the brake trigger Checking the inertia brake releaseMuffler Replacing the starter cord StarterTensioning the recoil spring Replacing the return and drive springsSpark plug Air filterLubricating the bar tip sprocket Needle bearing lubricationTemperature -5C 23F or colder Air Injection centrifugal cleaningCooling system Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions1150341-95 ´z+RB3¶55¨ ´z+RB3¶55¨

445 EPA II, 445e EPA II, 450e EPA II specifications

Husqvarna is a name synonymous with power and durability, especially when it comes to its line of chainsaws like the Husqvarna 445 EPA II, 445e EPA II, and 450e EPA II. These models combine advanced technology and ergonomic design to fulfill the needs of both professional users and homeowners.

The Husqvarna 445 EPA II chainsaw is designed for versatility and ease of use. It boasts a 45.7cc engine, providing a balance of power and weight ideal for various cutting tasks. The chainsaw features Husqvarna’s X-Torq engine technology, which reduces emissions and improves fuel efficiency. This means less downtime for refueling and a smaller ecological footprint, making it environmentally friendly. Additionally, the LowVib system minimizes vibration, which translates to reduced user fatigue over long periods of use.

The 445e EPA II takes similar principles and enhances them with increased efficiency and usability. This model includes the Air Injection system, which helps filter out larger dust and debris particles before reaching the air filter, ensuring consistent performance and a longer lifespan for the machine. Its lightweight design makes it easier to maneuver while the front handle is ergonomically shaped for a secure grip. The easy-start feature allows users to get going quickly with minimal effort.

Moving up the line, the Husqvarna 450e EPA II offers more power, featuring a slightly larger engine and an improved cutting capacity. This model is perfect for heavy-duty tasks, from felling trees to cutting firewood. Like its predecessors, it employs X-Torq engine technology and also includes the Quick Release Air Filter, making maintenance easier and faster. The robust design and advanced security features—such as the inertia-activated chain brake—ensure safe operation even under challenging conditions.

Overall, the Husqvarna 445 EPA II, 445e EPA II, and 450e EPA II chainsaws represent a commitment to safety, efficiency, and user comfort. The integration of modern technological features, coupled with Husqvarna's reputation for quality workmanship, makes these chainsaws ideal choices for anyone looking to tackle a range of outdoor cutting applications with confidence.
Top Page Image Contents