Husqvarna 445 EPA II, 445e EPA II, 450e EPA II Air filter, Spark plug, Needle bearing lubrication

Page 33

MAINTENANCE

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly.

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents English EPA II 445e EPA 450e EPAKEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth General advice on adjusting depth gauge settingTensioning the chain Adjustment of depth gauge setting445 445e, 450eChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Fitting the bar and chain Assembly445 445e, 450eAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking the brake trigger Checking the inertia brake releaseMuffler Replacing the starter cord StarterTensioning the recoil spring Replacing the return and drive springsSpark plug Air filterLubricating the bar tip sprocket Needle bearing lubricationTemperature -5C 23F or colder Air Injection centrifugal cleaningCooling system Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions1150341-95 ´z+RB3¶55¨ ´z+RB3¶55¨

445 EPA II, 445e EPA II, 450e EPA II specifications

Husqvarna is a name synonymous with power and durability, especially when it comes to its line of chainsaws like the Husqvarna 445 EPA II, 445e EPA II, and 450e EPA II. These models combine advanced technology and ergonomic design to fulfill the needs of both professional users and homeowners.

The Husqvarna 445 EPA II chainsaw is designed for versatility and ease of use. It boasts a 45.7cc engine, providing a balance of power and weight ideal for various cutting tasks. The chainsaw features Husqvarna’s X-Torq engine technology, which reduces emissions and improves fuel efficiency. This means less downtime for refueling and a smaller ecological footprint, making it environmentally friendly. Additionally, the LowVib system minimizes vibration, which translates to reduced user fatigue over long periods of use.

The 445e EPA II takes similar principles and enhances them with increased efficiency and usability. This model includes the Air Injection system, which helps filter out larger dust and debris particles before reaching the air filter, ensuring consistent performance and a longer lifespan for the machine. Its lightweight design makes it easier to maneuver while the front handle is ergonomically shaped for a secure grip. The easy-start feature allows users to get going quickly with minimal effort.

Moving up the line, the Husqvarna 450e EPA II offers more power, featuring a slightly larger engine and an improved cutting capacity. This model is perfect for heavy-duty tasks, from felling trees to cutting firewood. Like its predecessors, it employs X-Torq engine technology and also includes the Quick Release Air Filter, making maintenance easier and faster. The robust design and advanced security features—such as the inertia-activated chain brake—ensure safe operation even under challenging conditions.

Overall, the Husqvarna 445 EPA II, 445e EPA II, and 450e EPA II chainsaws represent a commitment to safety, efficiency, and user comfort. The integration of modern technological features, coupled with Husqvarna's reputation for quality workmanship, makes these chainsaws ideal choices for anyone looking to tackle a range of outdoor cutting applications with confidence.
Top Page Image Contents