Husqvarna 96045000410 To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjustmowertodesiredcuttingheight(See“TOADJUST MOWER CUTTING HEIGHT” in this section of manual).

•Withmowerindesiredheightofcutposition,gaugewheels should be assembled so they are slightly off the ground. Installgaugewheelinappropriatehole.Tightensecurely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch.

TO STOP MOWER BLADES - disengage attachment clutch control.

S

FIG. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH20K46 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionMaintenance Lubrication ChartBlade Care BatteryTractor Blade Removal See FigEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigReplacing Battery See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH20K46 96045000410, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH20K46 96045000410, Product no 45 Drive Washer Harden .793 x 1.637 x Spark Arrester KIT EngineEngine Kohler Model No. SV600 Steering Assembly Tractor - Model Number YTH20K46 96045000410, Product no 45 Decals Wheels and TiresSeat Assembly 532 40 SeatMower Deck KEY Part NO. no Description Mower Lift 100Limited Warranty Husqvarna S Obligations Under the Warranty 532 42 41-94 Rev 12.02.08 BAD

532 42 41-94, 96045000410 specifications

The Husqvarna 532 42 41-94,96045000410 represents a significant advancement in lawn care technology, designed for those who seek efficiency without compromising on performance. This innovative cutting deck, primarily intended for ride-on mowers, showcases an array of features that enhance its usability and effectiveness, making it a favored choice among homeowners and landscaping professionals alike.

One of the standout characteristics of the Husqvarna cutting deck is its robust construction, which ensures durability even in the toughest mowing conditions. Made with high-quality materials, this model is engineered to withstand the rigors of consistent use, providing reliability season after season. The deck's design allows for efficient grass collection, minimizing clumping and ensuring an even cut, which is essential for maintaining a healthy lawn.

The Husqvarna 532 42 41-94,96045000410 is equipped with advanced cutting technologies that enhance its mowing capabilities. It features a mower deck with a unique dual-blade system that significantly improves cutting efficiency. This dual-blade system allows for finer clippings, promoting better mulching and returning vital nutrients back to the soil. This not only supports a healthier lawn but also reduces the frequency of bagging.

Additionally, this cutting deck includes adjustable cutting heights, providing the flexibility to tailor your mow to various grass types and seasonal growth patterns. With several height options available, users can achieve the desired lawn appearance with ease. The ergonomic design of the cutting deck also features ample discharge openings that minimize clogging, ensuring smoother operation during prolonged use.

Another highlight of the Husqvarna cutting deck is its compatibility with a range of Husqvarna lawn tractors, making it a versatile attachment for those who already own compatible models. This practicality extends to its easy installation process, allowing users to quickly switch between attachments as needed.

Safety features have not been overlooked in the design of the Husqvarna 532 42 41-94,96045000410. The cutting deck comes equipped with safety shields and mechanisms that prevent accidental injuries, making it suitable for a variety of users. Coupled with high-performance engine specifications, this cutting deck is not only efficient but also ensures optimum safety.

In conclusion, the Husqvarna 532 42 41-94,96045000410 cutting deck stands out for its durability, innovative technologies, and user-friendly features. Whether you are a homeowner looking to maintain your lawn or a professional landscaper, this cutting deck is engineered to meet your mowing needs, providing a seamless and effective solution for lawn care.
Top Page Image Contents