Husqvarna 532 42 41-94 To Replace Mower Blade Drive Belt See Fig, To Check Brake, Belt Removal

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 30)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pulleys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "To Install Mower" in this section of manual).

IDLER

PULLEYS

MANDREL

PULLEY

MANDREL

PULLEY

FIG. 30

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 31)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Remove belt from stationary idler (A) and clutching idler (B).

3.Remove belt from centerspan idler (C).

4.Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (D).

5.Remove belt downward from engine pulley (E).

6.Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

2.Pull belt toward front of tractor and roll belt onto engine pulley (E).

3.Pull belt toward rear of tractor. Carefully work belt down around transaxle input pulley (D). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (C).

5.Install belt through stationary idler (A) and clutching idler (B).

6.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

7.Install mower (See “TO INSTALL MOWER” section in

this manual).

 

E

 

F

A

 

B

G

 

C

 

D

02952

FIG. 31

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents YTH20K46 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Attachment Clutch Switch Disengaged Engaged HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsLubrication Chart MaintenanceTractor BatteryBlade Care Blade Removal See FigEngine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigsTo Remove Mower See Fig Install belt on engine pulley M To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model Number YTH20K46 96045000410, Product no 45 SchematicElectrical KEY Part Description Chassis Tractor - Model Number YTH20K46 96045000410, Product no 45 Drive Washer Harden .793 x 1.637 x Engine Spark Arrester KITEngine Kohler Model No. SV600 Steering Assembly Tractor - Model Number YTH20K46 96045000410, Product no 45 Wheels and Tires Decals532 40 Seat Seat AssemblyMower Deck KEY Part NO. no Description 100 Mower LiftLimited Warranty Husqvarna S Obligations Under the Warranty 532 42 41-94 Rev 12.02.08 BAD

532 42 41-94, 96045000410 specifications

The Husqvarna 532 42 41-94,96045000410 represents a significant advancement in lawn care technology, designed for those who seek efficiency without compromising on performance. This innovative cutting deck, primarily intended for ride-on mowers, showcases an array of features that enhance its usability and effectiveness, making it a favored choice among homeowners and landscaping professionals alike.

One of the standout characteristics of the Husqvarna cutting deck is its robust construction, which ensures durability even in the toughest mowing conditions. Made with high-quality materials, this model is engineered to withstand the rigors of consistent use, providing reliability season after season. The deck's design allows for efficient grass collection, minimizing clumping and ensuring an even cut, which is essential for maintaining a healthy lawn.

The Husqvarna 532 42 41-94,96045000410 is equipped with advanced cutting technologies that enhance its mowing capabilities. It features a mower deck with a unique dual-blade system that significantly improves cutting efficiency. This dual-blade system allows for finer clippings, promoting better mulching and returning vital nutrients back to the soil. This not only supports a healthier lawn but also reduces the frequency of bagging.

Additionally, this cutting deck includes adjustable cutting heights, providing the flexibility to tailor your mow to various grass types and seasonal growth patterns. With several height options available, users can achieve the desired lawn appearance with ease. The ergonomic design of the cutting deck also features ample discharge openings that minimize clogging, ensuring smoother operation during prolonged use.

Another highlight of the Husqvarna cutting deck is its compatibility with a range of Husqvarna lawn tractors, making it a versatile attachment for those who already own compatible models. This practicality extends to its easy installation process, allowing users to quickly switch between attachments as needed.

Safety features have not been overlooked in the design of the Husqvarna 532 42 41-94,96045000410. The cutting deck comes equipped with safety shields and mechanisms that prevent accidental injuries, making it suitable for a variety of users. Coupled with high-performance engine specifications, this cutting deck is not only efficient but also ensures optimum safety.

In conclusion, the Husqvarna 532 42 41-94,96045000410 cutting deck stands out for its durability, innovative technologies, and user-friendly features. Whether you are a homeowner looking to maintain your lawn or a professional landscaper, this cutting deck is engineered to meet your mowing needs, providing a seamless and effective solution for lawn care.
Top Page Image Contents