Husqvarna 96045000410, 532 42 41-94 To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 32)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 32

TO START ENGINE WITH A WEAK BATTERY (See Fig. 33)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 33

REPLACING BATTERY (See Fig. 34)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

SEAT PAN

02602

TERMINAL

 

NUT

COVER

 

 

BOLT

 

 

POSITIVE

 

NEGATIVE

(RED)

 

 

(BLACK)

CABLE

 

 

CABLE

 

02603

FIG. 34

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH20K46 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionMaintenance Lubrication ChartBlade Care BatteryTractor Blade Removal See FigEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigReplacing Battery See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH20K46 96045000410, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH20K46 96045000410, Product no 45 Drive Washer Harden .793 x 1.637 x Spark Arrester KIT EngineEngine Kohler Model No. SV600 Steering Assembly Tractor - Model Number YTH20K46 96045000410, Product no 45 Decals Wheels and TiresSeat Assembly 532 40 SeatMower Deck KEY Part NO. no Description Mower Lift 100Limited Warranty Husqvarna S Obligations Under the Warranty 532 42 41-94 Rev 12.02.08 BAD

532 42 41-94, 96045000410 specifications

The Husqvarna 532 42 41-94,96045000410 represents a significant advancement in lawn care technology, designed for those who seek efficiency without compromising on performance. This innovative cutting deck, primarily intended for ride-on mowers, showcases an array of features that enhance its usability and effectiveness, making it a favored choice among homeowners and landscaping professionals alike.

One of the standout characteristics of the Husqvarna cutting deck is its robust construction, which ensures durability even in the toughest mowing conditions. Made with high-quality materials, this model is engineered to withstand the rigors of consistent use, providing reliability season after season. The deck's design allows for efficient grass collection, minimizing clumping and ensuring an even cut, which is essential for maintaining a healthy lawn.

The Husqvarna 532 42 41-94,96045000410 is equipped with advanced cutting technologies that enhance its mowing capabilities. It features a mower deck with a unique dual-blade system that significantly improves cutting efficiency. This dual-blade system allows for finer clippings, promoting better mulching and returning vital nutrients back to the soil. This not only supports a healthier lawn but also reduces the frequency of bagging.

Additionally, this cutting deck includes adjustable cutting heights, providing the flexibility to tailor your mow to various grass types and seasonal growth patterns. With several height options available, users can achieve the desired lawn appearance with ease. The ergonomic design of the cutting deck also features ample discharge openings that minimize clogging, ensuring smoother operation during prolonged use.

Another highlight of the Husqvarna cutting deck is its compatibility with a range of Husqvarna lawn tractors, making it a versatile attachment for those who already own compatible models. This practicality extends to its easy installation process, allowing users to quickly switch between attachments as needed.

Safety features have not been overlooked in the design of the Husqvarna 532 42 41-94,96045000410. The cutting deck comes equipped with safety shields and mechanisms that prevent accidental injuries, making it suitable for a variety of users. Coupled with high-performance engine specifications, this cutting deck is not only efficient but also ensures optimum safety.

In conclusion, the Husqvarna 532 42 41-94,96045000410 cutting deck stands out for its durability, innovative technologies, and user-friendly features. Whether you are a homeowner looking to maintain your lawn or a professional landscaper, this cutting deck is engineered to meet your mowing needs, providing a seamless and effective solution for lawn care.
Top Page Image Contents