Husqvarna 96045000410 Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 12

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several at- tempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may re- quire an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•Theattachmentscanalsobeusedduringtheenginewarm- up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents YTH20K46 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigService REMINDER/HOUR Meter Using the Reverse Operation SystemReverse Operation System ROS See Fig To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance Lubrication ChartBattery TractorBlade Care Blade Removal See FigEngine Cleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigsTo Remove Mower See Fig Install belt on engine pulley M Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH20K46 96045000410, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH20K46 96045000410, Product no 45 Drive Washer Harden .793 x 1.637 x Spark Arrester KIT EngineEngine Kohler Model No. SV600 Steering Assembly Tractor - Model Number YTH20K46 96045000410, Product no 45 Decals Wheels and TiresSeat Assembly 532 40 SeatMower Deck KEY Part NO. no Description Mower Lift 100Limited Warranty Husqvarna S Obligations Under the Warranty 532 42 41-94 Rev 12.02.08 BAD

532 42 41-94, 96045000410 specifications

The Husqvarna 532 42 41-94,96045000410 represents a significant advancement in lawn care technology, designed for those who seek efficiency without compromising on performance. This innovative cutting deck, primarily intended for ride-on mowers, showcases an array of features that enhance its usability and effectiveness, making it a favored choice among homeowners and landscaping professionals alike.

One of the standout characteristics of the Husqvarna cutting deck is its robust construction, which ensures durability even in the toughest mowing conditions. Made with high-quality materials, this model is engineered to withstand the rigors of consistent use, providing reliability season after season. The deck's design allows for efficient grass collection, minimizing clumping and ensuring an even cut, which is essential for maintaining a healthy lawn.

The Husqvarna 532 42 41-94,96045000410 is equipped with advanced cutting technologies that enhance its mowing capabilities. It features a mower deck with a unique dual-blade system that significantly improves cutting efficiency. This dual-blade system allows for finer clippings, promoting better mulching and returning vital nutrients back to the soil. This not only supports a healthier lawn but also reduces the frequency of bagging.

Additionally, this cutting deck includes adjustable cutting heights, providing the flexibility to tailor your mow to various grass types and seasonal growth patterns. With several height options available, users can achieve the desired lawn appearance with ease. The ergonomic design of the cutting deck also features ample discharge openings that minimize clogging, ensuring smoother operation during prolonged use.

Another highlight of the Husqvarna cutting deck is its compatibility with a range of Husqvarna lawn tractors, making it a versatile attachment for those who already own compatible models. This practicality extends to its easy installation process, allowing users to quickly switch between attachments as needed.

Safety features have not been overlooked in the design of the Husqvarna 532 42 41-94,96045000410. The cutting deck comes equipped with safety shields and mechanisms that prevent accidental injuries, making it suitable for a variety of users. Coupled with high-performance engine specifications, this cutting deck is not only efficient but also ensures optimum safety.

In conclusion, the Husqvarna 532 42 41-94,96045000410 cutting deck stands out for its durability, innovative technologies, and user-friendly features. Whether you are a homeowner looking to maintain your lawn or a professional landscaper, this cutting deck is engineered to meet your mowing needs, providing a seamless and effective solution for lawn care.
Top Page Image Contents