Husqvarna 96043005200 manual To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

J

K

L

FIG. 7

TO USE CRUISE CONTROL - J (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

A

FIG.9

FIG. 8

•Put attachment lift lever in desired cutting height slot.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH 2146 XP CA General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig Stopping See FigSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigReverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolineMowing Tips Purge TransmissionMaintenance Lubrication ChartBlade Care TractorBrake Operation TiresEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic SCH13Electrical KEY Part Description Chassis 239Tractor - Model Number YTH2146XP 96043005200, Product no 43 Drive 196Tractor - Model Number YTH2146XP 96043005200, Product no 43 Engine Engine Kawa Model No. FH641 Steering Assembly 532 19 Wheel, Steering Seat Assembly 532 40 SeatDecals Wheels and TiresMower Deck KEY Part NO. no Description Mower Lift 100Suggested Guide for Sighting Slopes for Safe Operation 532 41 88-57 12-12-07 SBW

96043005200 specifications

The Husqvarna 96043005200 is a powerful and versatile lawn mower designed to cater to both residential and professional gardening needs. Renowned for its superior engineering, this model stands out due to its combination of cutting-edge technology, innovative design, and reliability.

One of the main features of the Husqvarna 96043005200 is its efficient cutting system. Equipped with a robust engine, it offers a powerful performance that enables it to tackle a variety of grass types and terrains. The mower has an adjustable cutting height, allowing users to customize the grass length according to their preference and the specific requirements of their lawn. With its wide cutting deck, the mower can cover a larger area in shorter time, making lawn care faster and more efficient.

In terms of technology, the Husqvarna 96043005200 incorporates Smart Start technology, which simplifies the starting process. This feature decreases resistance in the starter cord, enabling easy initiation of the engine even after prolonged periods of inactivity. Additionally, it is designed with a compact structure that allows for easy maneuvering around tighter spaces and obstacles in the garden.

Operator comfort is also a priority for the Husqvarna 96043005200. The ergonomic handle is adjustable, ensuring that users of various heights can operate the mower comfortably. Moreover, the design includes vibration dampening technologies, reducing the strain on the operator’s hands and arms during prolonged use. This focus on ergonomics not only enhances comfort but also improves efficiency and productivity.

Durability is another characteristic that makes the Husqvarna 96043005200 a preferred choice among homeowners and professionals alike. The construction materials are robust, ensuring that the mower can withstand the rigors of regular use. It is built to resist wear and tear, providing a reliable performance season after season.

In summary, the Husqvarna 96043005200 is an advanced lawn mower that integrates powerful performance with user-friendly features. Its efficient cutting system, innovative starting technology, ergonomic design, and durability make it an excellent choice for anyone looking to maintain a lush, healthy lawn. This model represents Husqvarna’s commitment to quality and excellence in lawn care equipment, promising users a superior mowing experience.
Top Page Image Contents