Husqvarna 96043005200 manual Engine

Page 16

MAINTENANCE

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

The transmission fan and cooling fins should be kept clean to assure proper cooling.

Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent pos- sible damage to seals, do not use high pressure water or steam to clean transaxle.

•Inspect cooling fan to be sure fan blades are intact and clean.

•Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory and fluid mainte- nance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature.

16

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs. 14 and 15)

Determine temperature range expected before oil change. All oil must meet API service classification SG-SL.

•Be sure tractor is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

•Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

•Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

 

OIL DRAIN VALVE

CLOSED AND

 

LOCKED

 

POSITION

 

YELLOW

DRAIN

CAP

TUBE

FIG. 14

•Unlock drain valve by pushing inward and turning counterclockwise.

•To open, pull out on the drain valve.

•After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

•Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve.

•Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

•Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick. Tighten cap onto the tube securely when finished.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents YTH 2146 XP CA Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking BRAKESee FigTo USE Throttle Control D See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To Move Forward and Backward See FigUsing the Reverse Operation System To Operate Mower See FigReverse Operation System ROS To Operate on HillsService REMINDER/HOUR Meter Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionMaintenance Lubrication ChartTractor Brake OperationBlade Care TiresEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic SCH13Electrical KEY Part Description Chassis 239Tractor - Model Number YTH2146XP 96043005200, Product no 43 Drive 196Tractor - Model Number YTH2146XP 96043005200, Product no 43 Engine Engine Kawa Model No. FH641 Steering Assembly 532 19 Wheel, Steering Seat Assembly 532 40 SeatDecals Wheels and TiresMower Deck KEY Part NO. no Description Mower Lift 100Suggested Guide for Sighting Slopes for Safe Operation 532 41 88-57 12-12-07 SBW

96043005200 specifications

The Husqvarna 96043005200 is a powerful and versatile lawn mower designed to cater to both residential and professional gardening needs. Renowned for its superior engineering, this model stands out due to its combination of cutting-edge technology, innovative design, and reliability.

One of the main features of the Husqvarna 96043005200 is its efficient cutting system. Equipped with a robust engine, it offers a powerful performance that enables it to tackle a variety of grass types and terrains. The mower has an adjustable cutting height, allowing users to customize the grass length according to their preference and the specific requirements of their lawn. With its wide cutting deck, the mower can cover a larger area in shorter time, making lawn care faster and more efficient.

In terms of technology, the Husqvarna 96043005200 incorporates Smart Start technology, which simplifies the starting process. This feature decreases resistance in the starter cord, enabling easy initiation of the engine even after prolonged periods of inactivity. Additionally, it is designed with a compact structure that allows for easy maneuvering around tighter spaces and obstacles in the garden.

Operator comfort is also a priority for the Husqvarna 96043005200. The ergonomic handle is adjustable, ensuring that users of various heights can operate the mower comfortably. Moreover, the design includes vibration dampening technologies, reducing the strain on the operator’s hands and arms during prolonged use. This focus on ergonomics not only enhances comfort but also improves efficiency and productivity.

Durability is another characteristic that makes the Husqvarna 96043005200 a preferred choice among homeowners and professionals alike. The construction materials are robust, ensuring that the mower can withstand the rigors of regular use. It is built to resist wear and tear, providing a reliable performance season after season.

In summary, the Husqvarna 96043005200 is an advanced lawn mower that integrates powerful performance with user-friendly features. Its efficient cutting system, innovative starting technology, ergonomic design, and durability make it an excellent choice for anyone looking to maintain a lush, healthy lawn. This model represents Husqvarna’s commitment to quality and excellence in lawn care equipment, promising users a superior mowing experience.
Top Page Image Contents