Husqvarna 96043005200 manual Tractor, Brake Operation, Blade Care, Tires, Blade Removal See Fig

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

BLADE CARE

For best results mower blades must be sharp. Replace worn, bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

 

02828

BLADE REMOVAL (See Fig. 13)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

MANDREL

ASSEMBLY

BLADE

CENTER

HOLE

STAR

BLADE BOLT

(SPECIAL)

FIG. 13

CHECK REVERSE OPERATION (ROS) SYSTEM

• When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

• When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents YTH 2146 XP CA II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unpack Carton AssemblyUnassembled Parts To Remove Tractor from CartonCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig To USE Throttle Control D See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System CharacteristicsTo Operate on Hills Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSADD Gasoline Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission Mowing TipsLubrication Chart MaintenanceTires TractorBrake Operation Blade CareEngine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Motion Drive Belt See Fig To Replace Mower Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigTo Check Brake Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when SCH13 SchematicElectrical KEY Part Description 239 ChassisTractor - Model Number YTH2146XP 96043005200, Product no 43 196 DriveTractor - Model Number YTH2146XP 96043005200, Product no 43 Engine Engine Kawa Model No. FH641 Steering Assembly 532 19 Wheel, Steering 532 40 Seat Seat AssemblyWheels and Tires DecalsMower Deck KEY Part NO. no Description 100 Mower LiftSuggested Guide for Sighting Slopes for Safe Operation 532 41 88-57 12-12-07 SBW

96043005200 specifications

The Husqvarna 96043005200 is a powerful and versatile lawn mower designed to cater to both residential and professional gardening needs. Renowned for its superior engineering, this model stands out due to its combination of cutting-edge technology, innovative design, and reliability.

One of the main features of the Husqvarna 96043005200 is its efficient cutting system. Equipped with a robust engine, it offers a powerful performance that enables it to tackle a variety of grass types and terrains. The mower has an adjustable cutting height, allowing users to customize the grass length according to their preference and the specific requirements of their lawn. With its wide cutting deck, the mower can cover a larger area in shorter time, making lawn care faster and more efficient.

In terms of technology, the Husqvarna 96043005200 incorporates Smart Start technology, which simplifies the starting process. This feature decreases resistance in the starter cord, enabling easy initiation of the engine even after prolonged periods of inactivity. Additionally, it is designed with a compact structure that allows for easy maneuvering around tighter spaces and obstacles in the garden.

Operator comfort is also a priority for the Husqvarna 96043005200. The ergonomic handle is adjustable, ensuring that users of various heights can operate the mower comfortably. Moreover, the design includes vibration dampening technologies, reducing the strain on the operator’s hands and arms during prolonged use. This focus on ergonomics not only enhances comfort but also improves efficiency and productivity.

Durability is another characteristic that makes the Husqvarna 96043005200 a preferred choice among homeowners and professionals alike. The construction materials are robust, ensuring that the mower can withstand the rigors of regular use. It is built to resist wear and tear, providing a reliable performance season after season.

In summary, the Husqvarna 96043005200 is an advanced lawn mower that integrates powerful performance with user-friendly features. Its efficient cutting system, innovative starting technology, ergonomic design, and durability make it an excellent choice for anyone looking to maintain a lush, healthy lawn. This model represents Husqvarna’s commitment to quality and excellence in lawn care equipment, promising users a superior mowing experience.
Top Page Image Contents