Husqvarna 532 42 32-01 To Replace Mower Blade Drive Belt See Fig, To Check Brake, Belt Removal

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 30)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION -

Work belt around both mandrel pulleys and idler pulleys.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower (See "To Install Mower" in this section of manual).

IDLER

PULLEYS

MANDREL

PULLEY

MANDREL

PULLEY

FIG. 30

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 31)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Remove belt from stationary idler (A) and clutching idler (B).

3.Remove belt from centerspan idler (C).

4.Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (D).

5.Remove belt downward from engine pulley (E).

6.Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

2.Pull belt toward front of tractor and roll belt onto engine pulley (E).

3.Pull belt toward rear of tractor. Carefully work belt down around transaxle input pulley (D). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (C).

5.Install belt through stationary idler (A) and clutching idler (B).

6.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

7.Install mower (See “TO INSTALL MOWER” section in

this manual).

 

E

 

F

A

 

B

G

 

C

 

D

02952

FIG. 31

21

Image 21
Contents YTH20K46 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Attachment Clutch Switch Disengaged Engaged HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Move Forward and Backward See FigTo Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS See Fig To Operate on HillsBefore Starting the Engine Service REMINDER/HOUR MeterCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsLubrication Chart MaintenanceTractor BatteryBlade Care Blade Removal See FigEngine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigsTo Remove Mower See Fig Install belt on engine pulley M To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model Number YTH20K46 96045000409, Product no 45 SchematicElectrical KEY Part Description Chassis Tractor - Model Number YTH20K46 96045000409, Product no 45 Drive Tractor - Model Number YTH20K46 96045000409, Product no 45 Engine Spark Arrester KITEngine Kohler Model No. SV600 Prem Husq SR Steering AssemblyTractor - Model Number YTH20K46 96045000409, Product no 45 Wheels and Tires Decals532 40 Seat Seat AssemblyMower Deck KEY Part NO. no Description 100 Mower LiftLimited Warranty Husqvarna S Obligations Under the Warranty 532 42 32-01 Rev 12.01.08 BAD

532 42 32-01, 96045000409 specifications

The Husqvarna 96045000409,532 42 32-01 is a highly versatile lawn mower that brings innovation and efficiency to your yard maintenance tasks. Designed for homeowners who seek ease of use combined with high performance, this model stands out as an effective solution for maintaining lawns of various sizes.

One of the main features of this lawn mower is its powerful engine. Equipped with a high-quality gasoline engine, the Husqvarna 96045000409 ensures that you have the necessary power to cut through thick grass and tougher terrain, making it suitable for both small and larger areas. The model's robust construction provides durability, ensuring that it can withstand the rigors of regular use.

The mower features a cutting width of 42 inches, allowing for wider cutting paths and reducing the time spent mowing. The adjustable cutting height allows users to choose the preferred grass length, which can be particularly useful for achieving a professional-looking lawn. With multiple height settings, users can adapt to different grass types and seasonal needs effectively.

Another notable characteristic is its self-propelling capability. The Husqvarna 96045000409 comes with an advanced drive system that propels the mower forward, reducing the physical effort required by the operator. This feature is particularly useful on sloped terrains or uneven lawns, where pushing a traditional mower could be cumbersome.

The mower is designed with user comfort in mind. Its ergonomic handle provides a secure grip and minimizes vibrations during operation, which can lead to fatigue. Furthermore, the mower is equipped with a reliable bagging system that efficiently collects grass clippings, ensuring that your lawn maintains a clean and manicured appearance.

In terms of technology, this mower incorporates Husqvarna's advanced engineering, promising exceptional performance. The model's design also emphasizes easy maintenance, featuring easily accessible components that simplify tasks such as oil changes and blade replacements.

Overall, the Husqvarna 96045000409,532 42 32-01 is an excellent choice for homeowners who value performance, ease of use, and durability in their lawn care equipment. Whether you have a sprawling yard or a modest lawn, this mower is engineered to meet your gardening needs and deliver outstanding results, season after season.