Husqvarna 960430172 To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 6)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

• Adjust mower to desired cutting height (See “TO AD-

JUST MOWER CUTTING HEIGHT” in the Operation

section of this manual).

• With mower in desired height of cut position, gauge

wheels should be assembled so they are slightly off

the ground. Install gauge wheel in appropriate hole

"ENGAGED" POSITION

ATTACHMENT CLUTCH SWITCH "DISENGAGED" POSITION

ATTACHMENT LIFT LEVER

HIGH POSITION

LOW

POSITION

with shoulder bolt, 3/8 washer, and 3/8-16 locknut and

tighten securely.

• Repeat for opposite side installing gauge wheel in same

adjustment hole.

027

DEFLECTOR

SHIELD

7

5

 

FIG. 7

GAUGE

WHEEL

MOUNTING

BRACKET

014 2 3

3/8-16

LOCKNUT

3/8 WASHER

SHOULDER

BOLT

 

GAUGE WHEEL

FIG. 6

TO OPERATE MOWER (See Fig. 7)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS).Anyattemptbytheoperatortotravelinthereversedirec- tion with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Move motion control lever to neutral (N) position.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before backing.

•Slowly move motion control lever to reverse (R) position to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

02828

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to

12slower position.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents YTH18542 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Steering WheelSeat Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigReverse Operation System ROS To Operate on HillsBefore Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigSee Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Schematic TRACTOR-MODEL Number YTH18542 96013000200, Product no 13TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 ElectricalKEY Part NO. NO. Description Chassis TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 Drive TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 Steering Assembly TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 Engine Optional EquipmentMower Lift 1331Seat Assembly Decals Wheels and TiresMower Deck TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 19 49-62 11.2.04 RD

960430172 specifications

The Husqvarna 960430172 is a premium garden tractor designed for those who seek performance, durability, and comfort in lawn care tasks. Known for its robust build and efficient features, this model stands out in the market for homeowners and professionals alike.

One of the primary characteristics of the Husqvarna 960430172 is its powerful engine. Equipped with a reliable Briggs & Stratton engine, it delivers excellent cutting performance, allowing users to tackle various lawn conditions effortlessly. The engine’s high torque and efficient fuel consumption provide long-lasting power while ensuring that the tractor can handle even the toughest grass. A convenient automatic transmission enhances the user experience by allowing for smooth and easy operation without the hassle of manual gear shifting.

The cutting deck is another highlight of the Husqvarna 960430172. With a cutting width of 42 inches, it ensures that users cover large areas in minimal time. The deck is made from durable materials designed to withstand regular wear and tear, while the effective mowing height adjustment allows for precision lawn care tailored to individual preferences. Additionally, the Air Induction mowing technology further enhances performance by improving grass lift for a clean and even cut.

Ergonomics is a significant focus in the design of the Husqvarna 960430172. The tractor features a comfortable, high-back seat with armrests, allowing for long hours of mowing without discomfort. The steering wheel is positioned for optimal control, making it easy to navigate challenging terrains. Its tight turning radius enhances maneuverability around flower beds and landscaping features, making it an ideal choice for complex yards.

The Husqvarna 960430172 also boasts advanced safety features. An integrated safety switch ensures that the mower cannot operate unless the operator is seated, reducing the risk of accidents. Easy-access controls and a clear dashboard contribute to user-friendly handling, while the sturdy construction ensures stability in various conditions.

In conclusion, the Husqvarna 960430172 garden tractor offers an impressive array of features and technologies tailored for effective lawn maintenance. Its powerful engine, durable cutting deck, ergonomic design, and safety features combine to deliver a superior mowing experience, making it a valuable addition to any homeowner’s gardening toolkit. With this tractor, users can expect reliability and performance that meets their lawn care needs with ease.
Top Page Image Contents