Husqvarna 960430172 To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Page 20

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

 

BOTTOM EDGE

MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 16

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

• Before making any necessary adjustments, check that both front links are equal in length.

• If links are not equal in length, adjust one link to same length as other link.

• To lower front of mower loosen nut “E” on both front links an equal number of turns.

• When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

• To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

• When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

• Recheck side-to-side adjustment.

20

MANDREL

"D"

"D"

FIG. 18

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 19

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 20)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

MANDREL PULLEY

IDLER PULLEYS

MANDREL

PULLEY

FIG. 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents YTH18542 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Seat Unassembled PartsSteering Wheel Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigReverse Operation System ROS To Operate on HillsBefore Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigSee Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Schematic TRACTOR-MODEL Number YTH18542 96013000200, Product no 13TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 ElectricalKEY Part NO. NO. Description Chassis TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 Drive TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 Steering Assembly TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 Engine Optional EquipmentMower Lift 1331Seat Assembly Decals Wheels and TiresMower Deck TRACTOR-MODEL Number YTH18542 96013000200, Product no 13 Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 19 49-62 11.2.04 RD

960430172 specifications

The Husqvarna 960430172 is a premium garden tractor designed for those who seek performance, durability, and comfort in lawn care tasks. Known for its robust build and efficient features, this model stands out in the market for homeowners and professionals alike.

One of the primary characteristics of the Husqvarna 960430172 is its powerful engine. Equipped with a reliable Briggs & Stratton engine, it delivers excellent cutting performance, allowing users to tackle various lawn conditions effortlessly. The engine’s high torque and efficient fuel consumption provide long-lasting power while ensuring that the tractor can handle even the toughest grass. A convenient automatic transmission enhances the user experience by allowing for smooth and easy operation without the hassle of manual gear shifting.

The cutting deck is another highlight of the Husqvarna 960430172. With a cutting width of 42 inches, it ensures that users cover large areas in minimal time. The deck is made from durable materials designed to withstand regular wear and tear, while the effective mowing height adjustment allows for precision lawn care tailored to individual preferences. Additionally, the Air Induction mowing technology further enhances performance by improving grass lift for a clean and even cut.

Ergonomics is a significant focus in the design of the Husqvarna 960430172. The tractor features a comfortable, high-back seat with armrests, allowing for long hours of mowing without discomfort. The steering wheel is positioned for optimal control, making it easy to navigate challenging terrains. Its tight turning radius enhances maneuverability around flower beds and landscaping features, making it an ideal choice for complex yards.

The Husqvarna 960430172 also boasts advanced safety features. An integrated safety switch ensures that the mower cannot operate unless the operator is seated, reducing the risk of accidents. Easy-access controls and a clear dashboard contribute to user-friendly handling, while the sturdy construction ensures stability in various conditions.

In conclusion, the Husqvarna 960430172 garden tractor offers an impressive array of features and technologies tailored for effective lawn maintenance. Its powerful engine, durable cutting deck, ergonomic design, and safety features combine to deliver a superior mowing experience, making it a valuable addition to any homeowner’s gardening toolkit. With this tractor, users can expect reliability and performance that meets their lawn care needs with ease.
Top Page Image Contents