Husqvarna 917.240461 To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

K

J

L

Fig. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjustmowertodesiredcuttingheight(See“TOADJUST MOWER CUTTING HEIGHT” in this section of manual).

•Withmowerindesiredheightofcutposition,gaugewheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch.

TO STOP MOWER BLADES -

Disengage attachment clutch control.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 917.240461 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningSpark Plugs Deck Washout Port See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Engine continues Schematic Tractor - Model Number 917.240461, Product NO. YTH20K46Electrical Electrical KEY Part DescriptionChassis Tractor - Model Number 917.240461, Product NO. YTH20K46 Drive KEY Part NO. NO. Description Engine KEY Part Description Steering Assembly 873 94 Nut Hex Jam Toplock 1/2-20 unf 532 18 Seat Assembly 532 42 SeatMower Lift 8787 100 101Mower Deck Only pulley/nut/washer and blade Decals Wheels and TiresModel K46BT Tufftorq Transaxle Model Number K46BTKohl Engine Model NO. SV600-3229 CrankshaftAdditional OIL PAN/LUBRICATION HEAD/VALVE/BREATHER Blower Housing & Baffles Engine Controls AIR INTAKE/FILTRATION Crankcase Blower Housing & BafflesCrankshaft Oil Pan/LubricationAir Intake/Filtration AccessoriesEngine Controls DecalsSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes 02.15.11 SR

917.240461 specifications

The Husqvarna 917.240461 is a powerful and versatile riding mower designed for homeowners looking to maintain their lawns with ease and efficiency. Renowned for its robust build and reliable performance, this model showcases a range of features tailored to maximize comfort and convenience.

At the heart of the 917.240461 is a 24 HP Kohler engine, known for its durability and power. This engine allows the mower to cut through thick grass with finesse, making lawn care less of a chore and more of a pleasure. The machine’s cutting deck is a 54-inch reinforced stamped deck, designed for superior cutting performance. This larger deck size not only speeds up the mowing process but also ensures a clean and even cut on various terrains.

One of the standout technologies in the Husqvarna 917.240461 is its pedal-operated hydrostatic transmission, which makes speed control remarkably smooth and effortless. This feature allows users to change speeds without having to manually shift gears, making the mowing experience more intuitive and less physically demanding.

In terms of comfort, the mower is equipped with a high-back seat designed to provide ample support during extended use. The ergonomic steering wheel contributes to user-friendly handling, ensuring that maneuvering around obstacles is hassle-free. Additionally, the 917.240461 features easy-access controls that allow operators to engage the blades and adjust the cutting height conveniently.

Safety is also a priority for Husqvarna, and the 917.240461 incorporates several design elements aimed at enhancing user safety. The mower is equipped with anti-scalp wheels that help prevent damage to the grass and the cutting deck, preserving the quality of your lawn while preventing mower imbalances.

This model also boasts a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharge options. This versatility ensures that homeowners can effectively manage their lawn clippings according to their specific needs and preferences.

Durability is another key characteristic of the Husqvarna 917.240461. The sturdy frame and heavy-duty construction combine to create a mower that can withstand the rigors of regular use while maintaining optimal performance year after year.

In conclusion, the Husqvarna 917.240461 is an exemplary riding mower that combines power, comfort, and versatility. With its advanced features and technologies, it stands out as an ideal solution for homeowners seeking to enhance their lawn care experience.
Top Page Image Contents