Husqvarna 917.240461 warranty Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 12

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several at- tempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F/10° C and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F/10° C and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs rough- ly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•Theattachmentscanalsobeusedduringtheenginewarm- up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold tem- peratures (below 32° F/10° C) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjust- ments section of this manual.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 917.240461 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigService REMINDER/HOUR Meter Using the Reverse Operation SystemReverse Operation System ROS See Fig To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning Spark PlugsIN-LINE Fuel Filter See Fig Deck Washout Port See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Storage OtherFuel System Engine OILTroubleshooting Points Engine continues Schematic Tractor - Model Number 917.240461, Product NO. YTH20K46Electrical Electrical KEY Part DescriptionChassis Tractor - Model Number 917.240461, Product NO. YTH20K46 Drive KEY Part NO. NO. Description Engine KEY Part Description Steering Assembly 873 94 Nut Hex Jam Toplock 1/2-20 unf 532 18 Seat Assembly 532 42 SeatMower Lift 8787 100 101Mower Deck Only pulley/nut/washer and blade Decals Wheels and TiresModel K46BT Tufftorq Transaxle Model Number K46BTKohl Engine Model NO. SV600-3229 CrankshaftAdditional OIL PAN/LUBRICATION HEAD/VALVE/BREATHER Blower Housing & Baffles Engine Controls AIR INTAKE/FILTRATION Blower Housing & Baffles CrankshaftCrankcase Oil Pan/LubricationAccessories Engine ControlsAir Intake/Filtration DecalsSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes 02.15.11 SR

917.240461 specifications

The Husqvarna 917.240461 is a powerful and versatile riding mower designed for homeowners looking to maintain their lawns with ease and efficiency. Renowned for its robust build and reliable performance, this model showcases a range of features tailored to maximize comfort and convenience.

At the heart of the 917.240461 is a 24 HP Kohler engine, known for its durability and power. This engine allows the mower to cut through thick grass with finesse, making lawn care less of a chore and more of a pleasure. The machine’s cutting deck is a 54-inch reinforced stamped deck, designed for superior cutting performance. This larger deck size not only speeds up the mowing process but also ensures a clean and even cut on various terrains.

One of the standout technologies in the Husqvarna 917.240461 is its pedal-operated hydrostatic transmission, which makes speed control remarkably smooth and effortless. This feature allows users to change speeds without having to manually shift gears, making the mowing experience more intuitive and less physically demanding.

In terms of comfort, the mower is equipped with a high-back seat designed to provide ample support during extended use. The ergonomic steering wheel contributes to user-friendly handling, ensuring that maneuvering around obstacles is hassle-free. Additionally, the 917.240461 features easy-access controls that allow operators to engage the blades and adjust the cutting height conveniently.

Safety is also a priority for Husqvarna, and the 917.240461 incorporates several design elements aimed at enhancing user safety. The mower is equipped with anti-scalp wheels that help prevent damage to the grass and the cutting deck, preserving the quality of your lawn while preventing mower imbalances.

This model also boasts a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharge options. This versatility ensures that homeowners can effectively manage their lawn clippings according to their specific needs and preferences.

Durability is another key characteristic of the Husqvarna 917.240461. The sturdy frame and heavy-duty construction combine to create a mower that can withstand the rigors of regular use while maintaining optimal performance year after year.

In conclusion, the Husqvarna 917.240461 is an exemplary riding mower that combines power, comfort, and versatility. With its advanced features and technologies, it stands out as an ideal solution for homeowners seeking to enhance their lawn care experience.
Top Page Image Contents