Husqvarna 917.240461 warranty Engine continues

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

Engine continues

1.

Faulty operator-safety presence control

1.

Check wiring, switches and connections. If not

 

to run when oper-

 

system.

 

corrected, contact an authorized service center/

 

ator leaves seat

 

 

 

department.

 

 

 

 

 

 

with attachment

 

 

 

 

 

clutch engaged

 

 

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

 

2.

Mower deck not level.

2.

Level mower deck.

 

 

3.

Buildup of grass, leaves, trash under mower.

3.

Clean underside of mower housing.

 

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

 

5.

Clogged mower deck vent holes from

5.

Clean around mandrels to open vent holes.

 

 

 

buildup of grass, leaves, and trash around

 

 

 

 

 

mandrels.

 

 

 

Mower blades will

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

 

not rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

 

 

Poor grass

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

discharge

2.

Travel speed too fast.

2.

Shift to slower speed.

 

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

 

4.

Mower deck not level.

4.

Level mower deck.

 

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

 

6.

Worn, bent or loose blade.

6.

Replace blade. Tighten blade bolt.

 

 

7.

Buildup of grass, leaves, trash under mower.

7.

Clean underside of mower housing.

 

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

 

10.

Improper blades used.

10.

Replace with blades listed in parts manual.

 

 

11.

Clogged mower deck vent holes from buildup

11.

Clean around mandrels to open vent holes.

 

 

 

of grass, leaves, trash around mandrels.

 

 

 

Headlight(s) not

1.

Switch is “OFF”.

1.

Turn switch “ON”.

 

working

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

(if so equipped)

3.

Faulty light switch.

3.

Check/replace light switch.

 

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

 

 

Battery will not

1.

Bad battery cell(s).

1.

Replace battery.

 

charge

2.

Poor cable connections.

2.

Check/clean all connections.

 

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

 

2.

Debris on steering plate (if equipped).

2.

See "CLEANING" in the maintenance section.

 

 

3.

Motion drive belt worn, damaged, or broken.

3.

Replace motion drive belt.

 

 

4.

Air trapped in transmission during

4.

Purge transmission.

 

 

 

shipment or servicing.

 

 

 

 

5.

Axle key missing.

5.

Install axle key at rear wheel. See "TO REMOVE

 

 

 

 

 

WHEEL" in the Service and Adjustments section.

 

 

 

 

 

 

 

Engine "back-

1.

Engine throttle control not set between

1.

Move throttle control between half and full speed

 

fires” when turn-

 

half and full speed (fast) position before

 

(fast) position before stopping engine.

 

 

stopping engine.

 

 

 

ing engine “OFF”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Engine dies when

1.

Reverse operation system (ROS) is not "ON"

1.

Turn ignition key to ROS "ON" position. See

 

tractor is shifted

 

while mower or other attachment is engaged.

 

Operation section.

 

into reverse

 

 

 

 

 

26

Image 26
Contents 917.240461 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningSpark Plugs Deck Washout Port See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Engine continues Schematic Tractor - Model Number 917.240461, Product NO. YTH20K46Electrical Electrical KEY Part DescriptionChassis Tractor - Model Number 917.240461, Product NO. YTH20K46 Drive KEY Part NO. NO. Description Engine KEY Part Description Steering Assembly 873 94 Nut Hex Jam Toplock 1/2-20 unf 532 18 Seat Assembly 532 42 SeatMower Lift 8787 100 101Mower Deck Only pulley/nut/washer and blade Decals Wheels and TiresModel K46BT Tufftorq Transaxle Model Number K46BTKohl Engine Model NO. SV600-3229 CrankshaftAdditional OIL PAN/LUBRICATION HEAD/VALVE/BREATHER Blower Housing & Baffles Engine Controls AIR INTAKE/FILTRATION Crankcase Blower Housing & BafflesCrankshaft Oil Pan/LubricationAir Intake/Filtration AccessoriesEngine Controls DecalsSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes 02.15.11 SR

917.240461 specifications

The Husqvarna 917.240461 is a powerful and versatile riding mower designed for homeowners looking to maintain their lawns with ease and efficiency. Renowned for its robust build and reliable performance, this model showcases a range of features tailored to maximize comfort and convenience.

At the heart of the 917.240461 is a 24 HP Kohler engine, known for its durability and power. This engine allows the mower to cut through thick grass with finesse, making lawn care less of a chore and more of a pleasure. The machine’s cutting deck is a 54-inch reinforced stamped deck, designed for superior cutting performance. This larger deck size not only speeds up the mowing process but also ensures a clean and even cut on various terrains.

One of the standout technologies in the Husqvarna 917.240461 is its pedal-operated hydrostatic transmission, which makes speed control remarkably smooth and effortless. This feature allows users to change speeds without having to manually shift gears, making the mowing experience more intuitive and less physically demanding.

In terms of comfort, the mower is equipped with a high-back seat designed to provide ample support during extended use. The ergonomic steering wheel contributes to user-friendly handling, ensuring that maneuvering around obstacles is hassle-free. Additionally, the 917.240461 features easy-access controls that allow operators to engage the blades and adjust the cutting height conveniently.

Safety is also a priority for Husqvarna, and the 917.240461 incorporates several design elements aimed at enhancing user safety. The mower is equipped with anti-scalp wheels that help prevent damage to the grass and the cutting deck, preserving the quality of your lawn while preventing mower imbalances.

This model also boasts a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharge options. This versatility ensures that homeowners can effectively manage their lawn clippings according to their specific needs and preferences.

Durability is another key characteristic of the Husqvarna 917.240461. The sturdy frame and heavy-duty construction combine to create a mower that can withstand the rigors of regular use while maintaining optimal performance year after year.

In conclusion, the Husqvarna 917.240461 is an exemplary riding mower that combines power, comfort, and versatility. With its advanced features and technologies, it stands out as an ideal solution for homeowners seeking to enhance their lawn care experience.