Husqvarna 917.240461 warranty Tractor, Blade Care, Blade Removal See Fig, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 14)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•

When the engine is running, any attempt by the operator

 

to leave the seat without first setting the parking brake

 

should shut off the engine.

•

When the engine is running and the attachment clutch

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade ap- proved by the manufacturer of your tractor. Using a blade not approved by the manu- facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 15)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

CENTER HOLE

is engaged, any attempt by the operator to leave the

seat should shut off the engine.

BATTERY

Fig. 15

• The attachment clutch should never operate unless

the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 14

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICEANDADJUSTMENTSsectionofthismanual).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 917.240461 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Toremovetractorfromcarton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigTo Transport See Figs Service REMINDER/HOUR MeterUsing the Reverse Operation System Reverse Operation System ROS See FigTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsSchedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Deck Washout Port See Fig CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Engine OIL StorageOther Fuel SystemTroubleshooting Points Engine continues Tractor - Model Number 917.240461, Product NO. YTH20K46 SchematicElectrical KEY Part Description ElectricalChassis Tractor - Model Number 917.240461, Product NO. YTH20K46 Drive KEY Part NO. NO. Description Engine KEY Part Description Steering Assembly 873 94 Nut Hex Jam Toplock 1/2-20 unf 532 18 532 42 Seat Seat Assembly8787 100 101 Mower LiftMower Deck Only pulley/nut/washer and blade Wheels and Tires DecalsTufftorq Transaxle Model Number K46BT Model K46BTCrankshaft Kohl Engine Model NO. SV600-3229Additional OIL PAN/LUBRICATION HEAD/VALVE/BREATHER Blower Housing & Baffles Engine Controls AIR INTAKE/FILTRATION Oil Pan/Lubrication Blower Housing & BafflesCrankshaft CrankcaseDecals AccessoriesEngine Controls Air Intake/FiltrationOnly Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationService Notes Service Notes 02.15.11 SR

917.240461 specifications

The Husqvarna 917.240461 is a powerful and versatile riding mower designed for homeowners looking to maintain their lawns with ease and efficiency. Renowned for its robust build and reliable performance, this model showcases a range of features tailored to maximize comfort and convenience.

At the heart of the 917.240461 is a 24 HP Kohler engine, known for its durability and power. This engine allows the mower to cut through thick grass with finesse, making lawn care less of a chore and more of a pleasure. The machine’s cutting deck is a 54-inch reinforced stamped deck, designed for superior cutting performance. This larger deck size not only speeds up the mowing process but also ensures a clean and even cut on various terrains.

One of the standout technologies in the Husqvarna 917.240461 is its pedal-operated hydrostatic transmission, which makes speed control remarkably smooth and effortless. This feature allows users to change speeds without having to manually shift gears, making the mowing experience more intuitive and less physically demanding.

In terms of comfort, the mower is equipped with a high-back seat designed to provide ample support during extended use. The ergonomic steering wheel contributes to user-friendly handling, ensuring that maneuvering around obstacles is hassle-free. Additionally, the 917.240461 features easy-access controls that allow operators to engage the blades and adjust the cutting height conveniently.

Safety is also a priority for Husqvarna, and the 917.240461 incorporates several design elements aimed at enhancing user safety. The mower is equipped with anti-scalp wheels that help prevent damage to the grass and the cutting deck, preserving the quality of your lawn while preventing mower imbalances.

This model also boasts a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharge options. This versatility ensures that homeowners can effectively manage their lawn clippings according to their specific needs and preferences.

Durability is another key characteristic of the Husqvarna 917.240461. The sturdy frame and heavy-duty construction combine to create a mower that can withstand the rigors of regular use while maintaining optimal performance year after year.

In conclusion, the Husqvarna 917.240461 is an exemplary riding mower that combines power, comfort, and versatility. With its advanced features and technologies, it stands out as an ideal solution for homeowners seeking to enhance their lawn care experience.
Top Page Image Contents