Husqvarna 96045003000 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

J

K

L

Fig. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 " during the cool season and to over 3"during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES -

Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place. (See Fig. 10)

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH2348 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerReverse Operation System ROS Service REMINDER/HOUR MeterUsing the Reverse Operation System To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig ANTI-SWAY BAR S Turn Steering Wheel Left and Position Mower See FigAttach Mower Side Suspension Arms a to Chassis See Fig To Level Mower Turn nut right Turn nut left To raise mowerTo Replace Motion Drive Belt See Fig Mower Drive Belt InstallationTo Replace Mower Blade Drive Belt See Fig Mower Drive Belt RemovalTo Check Brake To Start Engine with a Weak Battery See FigWeak or Dead Fully Charged Battery Front Wheel TOE-IN/CAMBERTo Adjust Choke Control REMOVAL/REPLACEMENTTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Wheels and Tires DecalsKEY Part Description Schematic SCH12Electrical Socket Asm. Bulb Twistlock 208 Chassis Drive 196Bolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr Spark Arrester KIT EngineEngine Power Rating Information KEY Part NO. NO. DescriptionSteering Assembly Seat Assembly Mower Deck KEY Part NO. NO. Description Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission 11.05.10 JA

532 44 05-66, 96045003000 specifications

The Husqvarna 96045003000,532 44 05-66 is a powerful and innovative riding mower designed for residential lawn care. This model stands out due to its combination of performance, durability, and user-friendly features, making it a popular choice among homeowners seeking an efficient mowing solution.

At the heart of the Husqvarna 96045003000 is its robust engine. It is equipped with a premium quality engine that offers reliable performance and excellent fuel efficiency. The powerful motor enables the mower to tackle even the toughest grass, ensuring a pristine finish to your lawn with every cut. Along with this efficiency, the mower is also designed to minimize emissions, promoting a more environmentally friendly operation.

A standout feature of this model is its advanced cutting deck technology. The 42-inch cutting deck size allows for a wide cutting path, reducing the number of passes needed to cover larger areas. The design of the cutting deck ensures even grass distribution and enhanced mulching capabilities, allowing users to finely chop grass clippings for better nutrient return to the soil.

Equipped with the latest in ergonomic design, the Husqvarna 96045003000 prioritizes user comfort. It features an adjustable seat that ensures a comfortable riding position for various user heights and preferences. The steering system provides precise control, making it easy to navigate around obstacles in your yard.

The mowing height can easily be adjusted to suit different grass types and conditions, providing versatility for varying lawn care needs. This adaptability allows homeowners to maintain their lawns at desired lengths for aesthetic appeal and health.

Additionally, Husqvarna incorporates advanced safety features into this model. The cutting blade automatically disengages when the operator leaves the seat, minimizing the risk of accidents. The mower also comes with easy-to-access controls to ensure that all functions are within reach, enhancing operational safety.

In conclusion, the Husqvarna 96045003000,532 44 05-66 offers an excellent balance of power, efficiency, and safety features. Its durable construction and advanced technology make it an essential tool for any homeowner looking to maintain a beautiful lawn with ease.
Top Page Image Contents